秋霞电影网午夜鲁丝片无码,真人h视频免费观看视频,囯产av无码片毛片一级,免费夜色私人影院在线观看,亚洲美女综合香蕉片,亚洲aⅴ天堂av在线电影猫咪,日韩三级片网址入口

同軸電纜施工工具

上傳人:san****019 文檔編號:16337915 上傳時間:2020-09-26 格式:PPT 頁數:29 大?。?.73MB
收藏 版權申訴 舉報 下載
同軸電纜施工工具_第1頁
第1頁 / 共29頁
同軸電纜施工工具_第2頁
第2頁 / 共29頁
同軸電纜施工工具_第3頁
第3頁 / 共29頁

下載文檔到電腦,查找使用更方便

9.9 積分

下載資源

還剩頁未讀,繼續閱讀

資源描述:

《同軸電纜施工工具》由會員分享,可在線閱讀,更多相關《同軸電纜施工工具(29頁珍藏版)》請在裝配圖網上搜索。

1、同軸電纜施工工具,同軸電纜的布放與屏蔽型雙絞線類似 使用符合同軸電纜結構特點的工具進行剪切及剝線 專用連接器及端接工具 雙絞線驗證與認證設備同樣適用于同軸電纜,,同軸電纜分類,同軸電纜結構,中心導體要與屏蔽層保持等距以確保信號傳輸性能 標準規定:屏蔽電纜的彎曲半徑應至少為電纜外徑的610倍,同軸電纜施工工具剪切,,,,,,,截面被壓扁,,,These just wont do,同軸電纜施工工具剪切,,正確的剪切工具,45074,45075,Data T - Cutter 剪線鉗 多股通信電纜,直徑0.5in.(12.7mm) 同軸電纜RG-59/U、RG-58、RG-6 適合于剪切軟線 柔軟的

2、手柄套便于握持 鎖定銷使工具便于裝在工具套中,同軸電纜施工工具剝線,Stripping coax F-style,45-262 Stripmaster,45-524 Coax Stripper,30-433 Combo Tool,同軸電纜施工工具剝線Coax Stripmaster,Spring action grips & strips Speeds up 2-step stripping Different blades for: RG6 RG59 RG6 Quad,45-262,同軸電纜施工工具剝線Stripping coax with the Stripmaster 45-262,1.

3、 Place cable in smaller hole ” protruding,2. Squeeze handles together firmly & quickly,3. Place cable in larger hole ” protruding, squeeze,4. Stripped cable,同軸電纜施工工具剝線Stripping with the Coax Stripper 45-524,1. Set sliding window to cable size,2. Place cable in stripper with 1/8” protruding,3. Rota

4、te stripper in direction of lettering,4. Remove cable from stripper,5. Remove slugs,6. Stripped cable,,同軸電纜施工工具剝線Adjusting the Coax Stripper 45-524,4. Check by restripping cable. What was the left side is now the right side upside down!,1. Remove hex wrench from handle,2. Turn stripper over,3. In

5、sert wrench into adjusting grommets. Adjust by rotating 1/3 of way around at a time,同軸電纜施工工具剝線Replacing the blade cassette,Pull front door open Lift cassette up & out Insert new cassette & close door,同軸電纜施工工具端接About “F” Connectors,One-piece Most preferred, easiest installation Two-piece More pullout

6、 strength Twist-on What twists on will twist off,The number one cause of video distribution problemsis tightening F connectors finger tight. Tighten them with an F connector tool.,同軸電纜施工工具端接 About “F” Connectors,Must be used for all open CATV outlets Eliminates leakage and ingress, which lead to poo

7、r signal quality,,同軸電纜施工工具端接F-Connector Tool,Using leverage to install an F connector will seat every connector properly Most video signal problems are caused by loose connections. Tighten all connectors with an F-Connector tool.,35-046,Thread connector onto end of tool,Push connector onto stripped

8、cable,同軸電纜施工工具端接Coax Strip & Crimp Tool,Cuts, Strips & Crimps RG-6 & RG-59 No need to carry separate tools Good for occasional contractor use,,30-433,同軸電纜施工工具端接Terminating coax - CrimpMaster,Consistency & repeatability More leverage, less installer fatigue The same crimp every time 28 interchangeabl

9、e dies For the installer with more than an occasional crimp to do,30-506,與Crimpmaster 配合使用的同軸電纜連接器壓接模塊,同軸電纜施工工具剝線Stripping coax - BNC,Accuracy, efficiency, repeatability,45-520 Coax Stripper,Cut center conductor with35-060 CenterConductor Cutter,同軸電纜施工工具剝線To use the 45-520,1. Set sliding window to

10、cable size,2. Place cable in stripper with 1/4” protruding,3. Rotate stripper in direction of lettering,4. Remove cable from stripper,5. Remove 1st two slugs,6. Remove 3rd slug by bending cable,同軸電纜施工工具剝線Center Conductor Cutter 35-060,1. Stripped cable,2. Lay side of cutter against white dielectr

11、ic,3. Finished cable,同軸電纜施工工具端接BNC/TNC Connectors,Primary use today is for video/security installations Was an early data connector Looks like a difficult termination, but can be the easiest,同軸電纜施工工具端接Three-piece BNC,Recommended Fastest Easiest Captive contact pin Gas-tight crimp,,Captive Contact Pi

12、n,,同軸電纜施工工具端接Two-piece BNC,Strip to Braid, Peel Back,Less expensive More labor No captive contact pin No gas tight crimp,同軸電纜施工工具端接Twist-on BNC,Quickest, easiest Least reliable No captive contact pin No gas-tight crimp Can be affected by thermal change Installers worst nightmare Intermittent failure

13、,同軸電纜施工工具端接Terminating BNC Connectors,1. Close CrimpMaster to 1/8” open,2. Place center contact pin point down into smallest crimp nest,Wrong side up,3. Place center conductor all the way into center contact pin and crimp,4. Rotate dielectric to bend back braiding,同軸電纜施工工具端接Terminating BNC Connect

14、ors,1. Seat connector body onto dielectric, underneath the braiding, listen for click of captive contact pin,2. Seat the ferrule against the connector body with equal, opposing force,3. Squeeze handles together completely,4. Finished Connector,同軸電纜施工工具端接Coax Strip & Crimp Tool 30-433,Cuts, Strips & Crimps RG-6 & RG-59 No need to carry separate tools Good for occasional contractor use No ratcheting leverage for crimping,,Yes, theyre used,,,,,No, they shouldnt,,線纜施工工具工具包,為滿足線纜施工需要,方便用戶,IDEAL為用戶提供不同配置的工具包/箱,

展開閱讀全文
溫馨提示:
1: 本站所有資源如無特殊說明,都需要本地電腦安裝OFFICE2007和PDF閱讀器。圖紙軟件為CAD,CAXA,PROE,UG,SolidWorks等.壓縮文件請下載最新的WinRAR軟件解壓。
2: 本站的文檔不包含任何第三方提供的附件圖紙等,如果需要附件,請聯系上傳者。文件的所有權益歸上傳用戶所有。
3.本站RAR壓縮包中若帶圖紙,網頁內容里面會有圖紙預覽,若沒有圖紙預覽就沒有圖紙。
4. 未經權益所有人同意不得將文件中的內容挪作商業或盈利用途。
5. 裝配圖網僅提供信息存儲空間,僅對用戶上傳內容的表現方式做保護處理,對用戶上傳分享的文檔內容本身不做任何修改或編輯,并不能對任何下載內容負責。
6. 下載文件中如有侵權或不適當內容,請與我們聯系,我們立即糾正。
7. 本站不保證下載資源的準確性、安全性和完整性, 同時也不承擔用戶因使用這些下載資源對自己和他人造成任何形式的傷害或損失。

相關資源

更多
正為您匹配相似的精品文檔

相關搜索

關于我們 - 網站聲明 - 網站地圖 - 資源地圖 - 友情鏈接 - 網站客服 - 聯系我們

copyright@ 2023-2025  zhuangpeitu.com 裝配圖網版權所有   聯系電話:18123376007

備案號:ICP2024067431-1 川公網安備51140202000466號


本站為文檔C2C交易模式,即用戶上傳的文檔直接被用戶下載,本站只是中間服務平臺,本站所有文檔下載所得的收益歸上傳人(含作者)所有。裝配圖網僅提供信息存儲空間,僅對用戶上傳內容的表現方式做保護處理,對上載內容本身不做任何修改或編輯。若文檔所含內容侵犯了您的版權或隱私,請立即通知裝配圖網,我們立即給予刪除!