喜歡這套資料就充值下載吧。。。資源目錄里展示的都可在線預覽哦。。。下載后都有，，請放心下載，，文件全都包含在內，，【有疑問咨詢QQ:1064457796 或 1304139763】
XXXX學校畢業設計說明書
目 錄
前言…………………………………………………………2
摘要…………………………………………………………4
設計題目和任務書………………………………………..5
緒論…………………………………………………………6
一、塑件工藝分析………………………………………..16
二、注射機型號的確定………………………………….19
三、注射模的結構設計………………………………….20
四、模具設計的有關計算……………………………….31
五、注射機有關工藝參數的校核………………………37
六、繪制模具總裝配圖和非標準零件工作圖………..43
七、注射模主要零件加工工藝規程的編制…………..44
八、設計小結……………………………………………..44
謝辭…………………………………………………………45
參考文獻……………………………………………………46
摘要
分析了香水蓋外殼塑件的結構特點，敘述了該塑件成型工藝、注射模的結構和工作原理，其原理是：采用定距螺釘和彈簧進行二次分型,用斜導柱外側抽芯,型芯頂出零件,進料時采用潛伏式澆口進料形式,當開模的時候,用球頭拉料桿把澆注系統凝料頂出,然后利用型芯內抽推板推出塑件,合模時用彈簧先復位,然后進行下一次成型開始。提高了生產效率。
關鍵詞：香水蓋；注射模；定距螺釘；彈簧；斜導柱；側抽芯；型芯；球頭拉料桿；推板
Abstract
Analyzed the structure characteristics of the perfume cover outer shell plastics piece， described the piece’s structure and work principle which model a craft and inject a mold， its principle ：adopt and certainly be apart from bolt and spring coil and carry on two cents type， use inclined lead a side outside the pillar and take out heart， type the heart crest spare parts， while entering and anticipating adoption incubate the type sprinkle into anticipate a form， while opening a mold， with the ball head pull and anticipate a pole sprinkle and note system and anticipate， then make use of and take out and push plank and release a plastics piece inside a heart，use spring coil and reset first while matching a mold， then carry on willing model a beginning next time.Raised to produce an efficiency.
Keyword：perfume cover；inject a mold；certainly be apart from bolt；spring coil； inclined to lead pillar；the side takes out heart；type heart；the ball head pulls to anticipate a pole；push plank
第 3 頁 共 3 頁