塑料包裝機構主傳動機構設計-二級展開式圓柱圓錐齒輪減速器【說明書+CAD】,說明書+CAD,塑料包裝機構主傳動機構設計-二級展開式圓柱圓錐齒輪減速器【說明書+CAD】,塑料包裝,機構,傳動,設計,二級,展開式,圓柱,圓錐,齒輪,減速器,說明書,仿單,cad 1 塑料包裝機構主傳動機構設計 二級展開式圓柱圓錐齒輪減速器 任務說明書 系 別： 機電工程系 專 業： 機械設計制造及其自動化 姓 名： 荊偉澤 學 號： 2005090221 指導教師： 賈毅超 2 目 錄 一 設計題目 .3 1塑料包裝機的傳動示意如圖所示。 .3 2已知條件 .3 3設計內容 .3 二 傳動裝置總體設計 .4 三 電動機的選擇 .4 四 運動和運動參數計算： .4 1分配傳動比 .4 2計算傳動裝置的運動和動力參數 .4 五 傳動零件的設計計算 .6 1普通 V帶的設計計算 .6 2閉式直齒輪圓錐齒輪傳動的設計計算 .8 3閉式直齒圓柱齒輪設計計算 .13 4.軸的設計 .17 1）高速軸的設計 .17 2） .中間軸的設計 .20 3）低速軸的設計 .24 六 軸承的校核 .27 1高速軸軸承的校核 .27 2.中速軸軸承校核 .28 3.高速軸軸承的校核 .30 七.減速器機體結構 .31 八鍵的設計 .33 1.高速軸鍵的設計與校核 .33 2.中間軸鍵的設計與校核 .33 3.低速軸鍵的設計與校核 .34 九減速器的各部位附屬零件的設計. .34 十防滑方式的確定 .35 1滾動軸承的潤滑 .35 2齒輪的潤滑 .35 3 一 設計題目 1塑料包裝機的傳動示意如圖所示。 2已知條件 1）凸輪的轉速 n/（r/min） 35 電動機的功率/KW 0.25 2)工作情況：兩班制，連續單向運轉，載荷有輕微沖擊，室內工作。 3）使用期限：10 年； 4）生產條件：一般機械廠，單件生產； 5）動力來源：電力，三項交流，電壓 380220V； 6）檢修間隔：三年一大修，二年一中修，半年一小修 3設計內容 1）擬定工作機構和傳動方案 2) 工作機構和運動學動力學分析 3）設計繪制減速器裝配圖一張 4）設計繪制零件圖三張 5）編寫設計計算說明書一份 4 二 傳動裝置總體設計 1) 組成：傳動裝置由電機、減速器、工作機組成。 2）特點：齒輪相對于軸承不對稱布置，因而沿齒向載荷分布不均勻，要求軸有較大的剛 度 3）傳動系統的作用：介于機械中原動機與工作機之間，主要將原動機的運動和動力傳給 工作機，在此起減速作用，并協調二者的轉速和轉矩。 三 電動機的選擇 查手冊 選電動機型號 YS7114 功率 0.25kw 380V 轉速 1400r/min 四 運動和運動參數計算： 1分配傳動比 分配傳動比：查手冊第十三章，表 132知 V帶 i7,開式圓柱齒輪 i8，圓錐齒 輪 i5；總傳動比：i =40；取 （帶輪） 04i帶 ， （減速器）0/4/1i減 取 （錐齒輪） 12.5 （柱齒輪）2/i 2計算傳動裝置的運動和動力參數 （1）0 軸電動機的轉速 =350r/min140 nIinI =140r/min 352.Ii I =35r/min140 nIinI 5 （2）各軸的功率 傳動總效率 帶的傳動效率： 0.961 軸圓錐滾子軸承的效率： 82 圓錐齒輪嚙合的效率： .53 軸圓錐滾子軸承的效率： 094 齒輪嚙合的效率： .75 軸圓錐滾子軸承的效率： 6 聯軸器的傳動效率： 0.97 總的傳動效率 1234567總 .8326總 各軸的功率： 012.5096.8IPKW0.5PKWI 34I219 2567.7II .8I 各軸的轉矩： 60.3539.109.51PITIn6417.mTNI 6.296.5.4II 938.I 0.189.109.53PITIn542.TNI 6 五 傳動零件的設計計算 1普通 V帶的設計計算 （1）確定 V帶的型號和帶輪的直徑 工況系數 由（設計說明書）11.5 K1.2A 計算功率 選取帶型由0K1.25ACP03PWC （設計說明書）11.15 Y 型 小帶輪的直徑 同理由表 11.6 取 125mD 大帶輪的直徑 取210i54D0 （2）計算帶長 求 m2 62.5m 求 1052 37. 初取中心距 120a 帶長 2LDam48L 基準長度 50m （3）求中心距和包角 中心距 12()84LaLDm 5062. 2(4506.)37.5 1am 小輪包角 2118aa 0542.801 7 （4）求帶根數 帶速 1.83m/s 160nvDv 傳動比 i=4 帶的根數 由表 11.8 由表 11.7 .4P0.89K 由表 11.20 由表 11.10 1.0LK0.1PW Z= pck = =4.76 取 Z=5 根0.3.619. 張緊力 20 25CKPFqvVZ =500 +（0.04 ） .318.08921.835 （由表 11.4 q=0.04/m） .0FN 軸上載荷 2sin0FZQ 142.85.Si 26.3Q 帶輪的結構 由 YS741電動機 知軸的直徑 14dm 故小帶輪的孔徑 V帶的尺寸 頂寬 6b 節寬 5.3p 高 4hm 輪緣尺寸 =4.7mm =1.6mmminhfinh e=8mm f=7mm =5mmm 帶輪計算直徑 D 大帶輪 214D102D 8 帶輪的外徑 0D10251.6ha1028.Dm 2 23 帶輪的寬度 B()2(51)827zef46B6.3 2閉式直齒輪圓錐齒輪傳動的設計計算 選材： 直齒錐齒輪的加工多為刨齒，不宜采用硬齒面，小齒輪用 45 鋼調質處理， 硬度為 取平均硬度為 ，大齒輪選用 45 鋼正火處理，2175HB230HB 硬度為 ，取平均硬度為 。619 齒面接觸強度計算（由于小齒輪更容易失效故按小齒輪設計）： 齒數 Z和精度等級 工業用齒應大于等于 14 選取小齒輪齒數 16Z 則大齒輪的齒數為 初取 ，2.501iZ 16Z240Z 估計 左右 由表 12.9 選 8級精度/Vms 使用系數 由表 12.9 KA 1.25KA 動載系數 由圖 12.9 0V 齒間載荷分配系數 kh 估計 10/KFAtNmb = = =0.928cos2i.5 9 = = =0.371cos21i2.51 = = =17.24ZVcs1z60.98 = = =107.822o4.37 =1.661.8cos2z =0.88 4.63Z 由此得 =1.285120.8KHz 齒向載荷分布系數 查課本表 及注釋 =1.9 2KH 載荷系數 KAV 1.25.3193.42 0.25669.0PTNmn6587TI 彈性系數 查課本表 ZE1189.ZMPa 節點區域系數 查課本圖 H262.5ZH 接觸最小安全系數 查課本表 limS1410limS 總工作時間 th83080th 應力循環次數 NL 96143.3011nt 10 993.01.321052NLi 接觸壽命系數 查課本圖 12-18 Z 12.NZ 接觸應力 =638.1H 670lim1.5ZSH H =590.521li2.N2 小齒輪大端分度圓的直徑 1d 1d24.73205.3ZKTEHR = 2.61.89.50.3245.8 演算圓周速度及 KFAtb =（1-0.50.3）45.84=39mm10.54ddmR =0.714m/s3.950661 nmvs =329.1N 247.1TFNtdm =221cos dRb0.35421981.6m.539./0/846KFAtNmb 確定傳動主要尺寸 11 大端模數 m = = =2.865 取 m=31dZ45.86 實際大端分度圓的直徑 =48mm2.0mz1d =120mm 5d2 錐距 R = 21Z23640.Rm 齒寬 b 0.39.87b9b 按齒根彎曲疲勞強度計算 齒形系數 查課本圖 12-30 =2.66 =2.31YFa1YFa2YFa 應力修正系數 查課本表 12-22 =1.64 =2.02 重合度系數 =0.710.750.75.2.21 齒間載荷分布系數 查課本表 12-10KF = 1.440.71YKF 載荷系數 KAVF 1.250.493.08 彎曲疲勞極限 查課本表 limF3()c6lim1MpaF =570Mpa2 彎曲最小安全系數 查課本表 12-14 =1.60liSliS 應力循環次 NL601350841nth8.061NL 8.62.2Li 83.2 彎曲壽命系數 查課本圖 12-24 = =1.0Y 1Y 12 尺寸系數 查課本圖 12.25 =1.0YX XY 許用彎曲應力 Flim1YFNS =420.160.MPa1FMPa li2 YXSF =396.75701.6a2a 驗算 4.123051KTYSFZmiR .73861.607. 5 1542Mpa 1F = F2.310546Ys 16.pa2F 傳動無嚴重過載，故不做靜強度校核 錐齒輪結構 148dm210d11(0.5).48.mRm221arcos.9.21068arctn/arctn3/4.2.6hR 13 arctn/arctn3.6/42.ffhRm19.b 3閉式直齒圓柱齒輪設計計算 材料的選取：小齒輪用 鋼調質處理，硬度 ，平均取為 。大452175HB230HB 齒輪用 鋼正火處理，硬度 ，平均取為 。619 齒面接觸疲勞計算： (1)初步計算： 軸的轉矩 1T 1438.TNm 查課本表 12-3，取齒寬系數 d0d 接觸疲勞極限應力 由課本圖 limH12.7()c67li1MpaH =620Mpa2 初步計算的許用接觸應力 0.90.9681li1MPaH 6031paH 52m2 2M 由表 取Ad85Ad 初步計算小齒輪直徑 1 14938.12531 20Tid mH = 取.7135dm 齒寬 b1035d6b (2)校核計算： 圓周速度 v1.466nms0.24v 14 精度等級 查課本表 12-6 選 8級精度 齒數 Z 初取 =181Z =722 模數 = 由表 12.3 取1dmZ368m 使用系數 查課本表 =1.25KA129KA 動載系數 查課本圖 =1.10VV 齒間載荷分布系數 查課本表 12-10，先求H 214938.29.46TFNtd829.4FNt 1.2589.4.36KAtNmb 8.m10 =1.65811.cos.83272z 4.3Z0.84Z 由此得 =1.28120.86KHzKH 齒向載荷分布系數 HK 310.61bABCbd =1.33621.70.0KH 載荷系數 K AV .51.836 2.35 15 彈性系數 查課本表 ZE12189.ZMPaE 節點區域系數 查課本圖 H62.5H 接觸最小安全系數 查課本表 limS40limS 接觸壽命系數 查課本圖 ZN1281.8ZN25 許用接觸應力 H6701.25lim1ZSH7.9MpaH.li2N 38.1 驗算 ： 21KTiZHEbd .35498.1189.250.8 a 7.6Mp H2 計算結果表明，觸疲勞強度較為合適，齒輪尺寸無需調整 (3)確定傳動主要尺寸實際分度圓直徑 D 因模數取標準值時，齒數已重新確定，但并未圓整。 故分度圓直徑不會改變，即 實際分度圓直徑 218dmz361dm 742 中心距 a12()()za 9090a 齒寬 取b36dm14bm236 16 (4)齒根彎曲疲勞強度驗算： 重合度系數 Y0.750.75.2.2168Y0.72Y 齒間載荷分布系數 查課本表KF1 =1.4240.72YKF 齒向載荷分布系數 358(.4)bh 查課本圖 12-14 =1.24 載荷系數 KKAVF 1.250.41.22.57K 齒形系數 查課本圖 YFa.Ya18Fa 應力修正系數 查課本表 = 1.82S159s2S 彎曲疲勞極限 查課本表 lim123()c7limMp 50aF 彎曲最小安全系數 查課本表 liSF41.2liS 彎曲壽命系數 查課本圖 YN12.1YN 尺寸系數 由圖 X.5.0YX 許用彎曲應力 Flim1FXS 580.12MPa51.2MpaFliYNSF 90.512a503.42pa 17 驗算： 21KTYFaSbdm .5473.261.5908MPa 8.1Mpa 1F2YFS 1.2110 齒輪端面與內機 壁距離 2 210 機蓋，機座肋厚 m,1 85.0,.1m8 軸承端蓋外徑 2D+（55.D2 5） 3d7077 82 八鍵的設計 1.高速軸鍵的設計與校核 根據 計手冊第四章，選用 圓128,1937.62dmTNm /1096GBT鍵 845 頭普通平 鍵（A 型），課本第七章表 7.1鑄鋼的許用擠壓應力 2MPap149834.6210.07MPadlh 所以鍵的強度滿足。 所選鍵為 強度合格；bl 2.中間軸鍵的設計與校核 根據 查手冊第四章，選用 圓275,867.10dmTNm /1096GBT63鍵 2 頭普通平鍵（A 型），本表 7.1鑄鋼料的許用擠壓應力 ；p 34 48657.106.532pTMPadlh 所選鍵的度滿足。 3.低速軸鍵的設計與校核 根據 查設手冊第四章，選用 鍵275,483.9dmTNm /1096GBT 圓頭普通平90214 鍵（A 型），查課本表 7.1鑄鋼料的許用擠壓應力 2p53.210.9874MPadlh 所選鍵的強度滿足。 九減速器的各部位附屬零件的設計. 1窺視孔蓋與窺視孔： 在減速器上部可以看到傳動零件嚙合處要開窺視孔, 大小只要夠手伸進操作可。 以便檢查齒面接觸斑點和齒側間隙,了解嚙合情況.潤滑油也由此注入機體內. 2放油螺塞 放油孔的位置設在油池最低處，并安排在不與其它部件靠近的一側，以便于放 油，放油孔用螺塞堵住并加封油圈以加強密封。 3油標 油標用來檢查油面高度，以保證有正常的油量.因此要安裝于便于觀察油面及油面穩定之 處即低速級傳動件附近；用帶有螺紋部分的油尺，油尺上的油面刻度線應按傳動件浸入深 度確定。 4通氣器 減速器運轉時，由于摩擦發熱,機體內溫度升高，氣壓增大，導致潤滑油從縫隙向外 滲漏,所以在機蓋頂部或窺視孔上裝通氣器，使機體內熱空氣自由逸處，保證機體內外壓 力均衡，提高機體有縫隙處的密封性，通氣器用帶空螺釘制成. 5啟蓋螺釘 為了便于啟蓋，在機蓋側邊的邊緣上裝一至二個啟蓋螺釘。在啟蓋時，可先擰動此螺釘頂 起機蓋；螺釘上的長度要大于凸緣厚度，釘桿端部要做成圓柱形伙半圓形，以免頂壞螺紋； 螺釘直徑與凸緣連接螺栓相同。 在軸承端蓋上也可以安裝取蓋螺釘,便于拆卸端蓋.對于需作軸向調整的套環,裝上二個螺 釘,便于調整. 6定位銷 為了保證剖分式機體的軸承座孔的加工及裝配精度，在機體聯接凸緣的長度方向兩端各安 35 置一個圓錐定位銷。兩銷相距盡量遠些，以提高定位精度。如機體是對稱的,銷孔位置不 應對稱布置. 7環首螺釘、吊環和吊鉤 為了拆卸及搬運，應在機蓋上裝有環首螺釘或鑄出吊鉤、吊環，并在機座上鑄出吊鉤。 8調整墊片 用于調整軸承間隙,有的起到調整傳動零件軸向位置的作用. 9密封裝置 在伸出軸與端蓋之間有間隙,必須安裝密封件,以防止漏油和污物進入機體內. 十防滑方式的確定 1滾動軸承的潤滑 滾動軸承的潤滑采用脂潤滑，它不易流失密封性好加脂周期長。 該滾動軸承的工作溫度不太高的可選鈣基潤滑脂，滾動軸承摩擦力大?？蛇x 1號潤滑 脂 GB491-87 2齒輪的潤滑 由于展開式齒輪的傳動速度比低，載荷大，油脂容易流失，所以采用粘度很高，防銹 性好的開式齒輪油。采用油池潤滑，自然冷卻，侵入油中的齒輪深度為 1-2個齒高， 采用液壓油 GB1118.1-1994. 附注： 參考數據 吳宗澤，羅圣國主編機械設計課程設計手冊。 邱宣懷主編機械設計。 編號 無錫太湖學院 畢業設計（論文） 相關資料 題目：單級減速機箱體和箱蓋工藝工裝設計 機電 系 機械工程及自動化專業 學 號： 　　　 0923199　　　　 學生姓名： 張亞東 指導教師： 　 鮑虹蘇（職稱：高工 ） （職稱： ） 2013年5月25日 目 錄 一、畢業設計（論文）開題報告 二、畢業設計（論文）外文資料翻譯及原文 三、學生“畢業論文（論文）計劃、進度、檢查及落實表” 四、實習鑒定表 無錫太湖學院 畢業設計（論文） 開題報告 題目：單級減速機箱體和箱蓋工藝工裝設計 信機 系 機械工程及自動化專業 學 號： 0923199 學生姓名： 張亞東 指導教師： 鮑虹蘇 （ 職稱：高工） （職稱： ） 2012年11月24日 課題來源 機械制造業是一個國家最基礎的行業，也決定了一個國家制造業的整體水平現在中國已經是一個制造大國，中國的制造業規模已經達到世界第四位，僅次于美國、日本和德國。 研究內容 本設計是針對減速機箱體工藝的制作，主要研究的是減速機箱蓋的工藝過程、減速機的底座的工藝過程、減速機箱體合裝后的工藝過程以及對該技術的測試和其實用性的研究。并由此做出了對現行的減速機的箱體的改造和進一步的完善。在這次的箱體工藝制造中，對一些主要程序比如說結合面聯接孔、鉆頂面螺紋底孔、攻螺紋、鉆側面測油孔、放油孔、螺紋底孔、沉孔、攻螺紋 等的研究。 擬采取的研究方法、技術路線、實驗方案及可行性分析 設計任務 1） 設計一個中等復雜的零件的加工工藝規程； 2） 設計一個專用夾具； 3） 編寫設計說明書。 根據設計任務做出減速機箱的基本設計任務 1）繪制零件工件圖一張； 2）繪制毛坯—零件合圖一張； 3）編制機械加工工藝規程卡片一套； 4）編寫設計說明書一份； 5）收集和研究原始資料，為夾具結構設計做好技術準備。 6）初步擬定夾具結構方案，繪制夾具結構草圖，進行必要的理論計算和分析。 選擇最佳的夾具結構方案，確定夾具精度和夾具總圖尺寸、公差配合與技術要求。 7） 繪制夾具總圖和主要非標準件零件圖，編寫設計說明書。 8）編制夾具特殊使用維護、操作、制造方面的說明或技術要求。 研究計劃及預期成果 研究計劃： 2012年11月12日-2012年12月25日：按照任務書要求查閱論文相關參考資料，填寫畢業設計開題報告書。 2013年1月11日-2013年3月5日：填寫畢業實習報告。 2013年3月8日-2013年3月14日：按照要求修改畢業設計開題報告。 2013年3月15日-2013年3月21日：學習并翻譯一篇與畢業設計相關的英文材料。 2013年3月22日-2013年4月11日：設計減速機箱體和箱蓋的結構并畫出相關草圖 2013年4月12日-2013年4月25日：完善設計所需的各種零件圖、夾具圖，并對設計的所有數據進行整理，做好撰寫畢業論文的準備。 2013年4月26日-2013年5月20日：畢業論文撰寫和修改工作。 預期成果： 機械制造技術設計是培養機械工程類專業學生應職應崗能力的重要實踐性教學環節，它要求學生能全面綜合地運用所學的理論和實踐知識，進行零件機械加工工藝規程和工藝裝備的設計。其基本目的是： 1） 培養工程意識。 2） 訓練基本技能。 3） 培養質量意識。 4） 培養規范意識。 特色或創新之處 1、 設計了一副可以多方面加工的夾具，減少了原材料的應用和所需的工時。 2、 設計了多種加工方案，并對其比較，選出最佳方案。 已具備的條件和尚需解決的問題 1、一是對鏜床的不熟悉，二是在公差與配合方面的知識所學較少。 2、學院圖書館相關資料有限，并且很多資料不外借處學校，設計此項目任務重工作量大物力條件有限以及經濟上的原因造成難以落實原材料加工出成品 3、經過努力，設計達到了預想的成功，由于條件的限制沒能加工出成品，但對于我自己來說已經學到了不少東西。 指導教師意見 指導教師簽名： 2011年 11 月 20 日 教研室（學科組、研究所）意見 教研室主任簽名： 年 月 日 系意見 主管領導簽名： 年 月 日 英文原文 Mineral product monorail reduction gear synopsis First:what is reducer Reducer is a dynamic communication agencies, the use of gear speed converters, motor rotational speed reducer to the Rotary to be few, and have greater torque institutions. The reducer role 1) velocity at the same time increase the output torque, torque output ratio by motor output by slowdown, but the attention should be paid to exceed the rated torque reducer. 2) the speed at the same time reduce the inertia load, the inertia of deceleration than reduced to the square. We can look at the General Motors has a value of inertia. ?????????? The type of reducer General helical gear reducer has reducer (including parallel shaft helical gear reducer, a worm reducer, bevel gear reducer, etc.), planetary gear reducer, Cycloid reducer, a worm reducer, a planetary friction CVT mechanical machines. ???????? Common reducer 1) worm reducer is the main characteristics of a reverse self-locking function, can be larger than a slowdown, input shaft and output shaft axis is not the same, nor in the same plane. But generally larger, transmission efficiency is not high, the accuracy is not high. 2) Harmonic Harmonic Drive reducer is controllable using flexible components to transfer elastic deformation and dynamic movement, not volume, high precision, but the disadvantage is that flexible wheel limited life, impatient shocks, rigidity and pieces of metal relatively poor. Not too high speed input. 3) planetary reducer its comparative advantage is compact structure, the return gap small, high precision, and have a long life span rated output torque can be done great. However, a price slightly expensive, the requirements of parts before assembly 1. Rolling cleaning with gasoline, kerosene other parts cleaning. All parts and Xiangbenna not allowed to have any impurities exist. Gear box and the inner wall (Worm), unprocessed surface has not been coated twice erosion-resistant oil paint, box has the outer surface coated primer and paint color (color requested by host). 2. Parts coated with a face wash after lubricants Second, the requirements of installation and adjustment 1. Rolling installation Rolling bearing inner ring should be installed at the shaft shoulder close to gap must not pass 0.05 mm thick Cypriot feet. 2. Bearing axial clearance of the clearance can not be adjusted bearings (such as deep groove ball bearings), axial clearance of 0.25 to 0.4 mm; the clearance adjustable bearing axial clearance numerical table. Click Tapered Roller Bearings axial clearance; angular contact ball bearing axial clearance 3. Gear (Worm) meshing tooth space available Cypriot side foot of lead or pressure. Will be lead wire on the alveolar, and then turning gear and squash lead wire, measuring two teeth side was crushed lead wire thickness and the size of which is adjacent teeth. 4. Tooth contact dot cylinder gear tooth contact Dot 2-10-4; bevel gear tooth contact Dot 2-11-4; Gearing contact Dot 2-12-4 Third, seal requirements 1. Box partition between the surface does not allow any pads filled, but can be coated or water glass sealant to ensure that the seal; 2. Assembly, the bolt tightening box, before using 0.05 mm Cypriot-foot inspection Covers Block with me and between the sealing surface; 3. Shaft seal should stretch to smear grease. The seal should be installed in strict accordance with the requirements Forth, lubrication requirements 1. Rationally determine the types of lubricants and greases and grades 2. Bearing lubrication fat, grease filled in the general Fatliquor space can be 1 / 2 to 2 / 3. 3. Lubricants should be regularly replaced, the new reducer used for the first time, the operation of oil-7 ~ 14 days, according to the situation can be after every 3 to 6 months for first oil. Fifth, the test requirements 1. Empty operation: at rated speed is, anti-running 1 to 2 hours; 2. Load test: at rated speed, rated load operation, the oil temperature balance to date. On the gear reducer, requested the pool temperature is not more than 35 oC, bearing temperature rise no more than 40 oC; the worm reducer, requested the pool temperature not more than 60 oC, bearing temperature of not more than 50 oC; 3. Entire testing process for the smooth operation, noise, not loosening the fixed link, sealed, not with the Sixth, packaging and transportation requirements 1. Protruding shaft and its annex should Oiler packaging; 2. Handling, lifting may not use screw rings and lug all of the above technical requirements are not necessarily listed, and sometimes also by other projects, mainly by the specific design requirements. Seventh. Technical requirements 1. Assembly, all parts cleaning with kerosene, gasoline Rolling cleansing, while the existence of any debris. Oil is not painted wall corrosion coatings twice; 2. Backlash with lead wire mesh test of not less than 0.16 mm, lead wire Backlash may not exceed the smallest of the four times; 3. Used Tu-color dot test. Tooth high point of contact by not less than 40% of contact spots on teeth not less than 50 per cent. Can be used when necessary, grinding or scraping after grinding to improve contacts; 4. Bearing axial clearance should be adjusted: φ40 0.05 - 0.1 mm, φ55 0.08 - 0.15 mm; 5. Test reducer subdivision surface, the contact surface and seal, oil spills are not allowed. Split-Tu allowed to paint or water glass seal and allow the use of any filler; 6. Engine lubricants to the contents N100 provisions height; Below I introduce our country reduction gear the development present situation First, the domestic reduction gear many by the gear drive, the worm drive primarily, but has the power and the load ratio generally is small, or velocity ratio great and mechanical efficiency excessively low question.Moreover, in the material quality and the technological level also has many weakness, the large-scale reduction gear question is specially more prominent, the service life is not long.The domestic use large-scale reduction gear (above 500kw), many from overseas (for example Denmark, Germany and so on) imports The 60's start few tooth reduction gears and so on difference transmission, cycloid pin gear transmission, overtone transmission which produces has the velocity ratio to be big, volume small, mechanical efficiency higher merit? .But its transmission theory limit, cannot transmit the oversized power, the power all must be smaller than generally 40kw. Because in the transmission theoretically, the technological level and the material quality aspect has not broken through, therefore, has not been able fundamentally to solve the transmission power in a big way, the velocity ratio big, the volume small, the weight light, mechanical efficiency higher these requests basically.The 90's initial period, the home appears three links (gear) the reduction gear, is one kind of outside stable motion gear drive reduction gear, it may realize the great velocity ratio, transmission load ability is also big. Its volume and the weight are all lighter than the dead axle speed reducer gear, the structure is simple, the efficiency is also high.Because this reduction gear three axle parallel structure, therefore caused the power/volume (or weight) the ratio is still small.Also its input axis and the output shaft on the identical spool thread, this do not have in the use many inconveniently. Not only Beijing Institute of Technology develops in successful " stable motion speed reducer gear " to have outside three link reduction gear merit, but also has the big power/weight (or volume) the ratio, as well as the input axis and the output shaft on identical spool thread merit, is at the domestic leading position.The home has the minority college and the factory and mining enterprise does the research work to in stable motion gear drive certain principles, has published some research paper, in has done some work using the cycloidal tooth crop rotation stable motion reduction gear. Second, the stable motion speed reducer gear principle of work synopsis, the stable motion speed reducer gear is refers to in a counter gear transmission, a gear in the stable motion generator actuation mean plane parallel motion, meshing through tooth profile between, actuates another tooth crop rotation dead axle to decelerate the rotation, the realization reduction gear function.The stable motion generator may use the parallelogram organization, either sine organization or cross slide organization.This achievement uses the parallelogram organization to take the stable motion generator. The stable motion generator may be the hypothesized use parallelogram organization, also may be the entity use parallelogram organization.Has the practical value stable motion gear mechanism for in counter gear organization, therefore may divide into the internal tooth crop rotation stable motion movement and the external tooth crop rotation stable motion movement two kind of situations.Outside the stable motion gear reduction organization, its internal tooth crop rotation stable motion movement, actuates the external gear and makes the deceleration rotation output.This organization also calls three links (gear) the reduction gear. As a result of the internal tooth crop rotation stable motion, two crank centers establish outside the annular gear tooth ring, therefore its size is not compact, cannot solve the volume major problem.? In stable motion gear reduction, its external tooth crop rotation stable motion movement, actuation internal tooth crop rotation deceleration rotation output.As a result of the external tooth crop rotation stable motion, two crank centers can establish in the external gear tooth ring, reduced the organization overall size greatly. Because in stable motion gear mechanism transmission efficiency high, volume small, input output coaxial line, therefore by widespread application prospect. Third, this project technical characteristic and key technologies? 1. this project technical characteristics, in this new " stable motion speed reducer gear " and domestic and foreign had the speed reducer gear compares, has the following characteristic: (1) velocity ratio scope is big, gets up from I=10, may reach most greatly several thousand.If manufactures the great velocity ratio the reduction gear, then demonstrates this reduction gear the merit.(2) transmission power scope is big: And may connect a body manufacture with the electric motor. (3) structure simple, the volume small, the weight is light.Reduces about 1/3 compared to the existing speed reducer gear.(4) mechanical efficiency is high.95 (5) this reduction gear input axis and the output shaft are on the identical spool thread.This reduction gear see Table 1 with other reduction gear performance comparison. Because lacks the data, various reduction gears power/load ratio which in the table arranges in order is most superior.? Table 1? Each kind of reduction gear comparison model power (kw) reduction gear ratio quality (kg) QI-450? 93 31.5 1820 ZSY-250? 95 31.5 540 NGW-92 88.1 31.5 577 SEW (Germany)? 90 28.61 1300 NP-100? 100 30 400 Note: NP-100 is in the stable motion speed reducer gear, the SEW reduction gear quality contains the electrical machinery.2. this project key technologies? May know by Figure 2, in “stable motion speed reducer gear " is by annular gear Z2, external gear Z1 and the parallelogram organization combination becomes.Its transmission principle is: The electrical machinery input rotary motion, the external tooth crop rotation parallel migration, its center of circle path is a circle, makes the dead axle rotation with it meshing annular gear. Because external tooth crop rotation parallel migration, therefore name stable motion gear mechanism.The gear parallel migration needs to have the auxiliary body help realization, may use (6~12) to sell the axis, the roller takes the hypothesized auxiliary stable motion organization, also may use the eccentric shaft to take the entity auxiliary stable motion organization.In the stable motion speed reducer gear key technologies and the essential craft are the composition parallelogram component size computation and the request processing precision, the gear teeth main parameter choice. These factors will all affect the transmission ability and the transmission quality.Overall speaking, the group cost reduction gear various spare parts all request to have the high precision, they will be deciding the reduction gear overall transmis3. this project survey this project has obtained the Chinese practical new patent, the patent number: ZL95227767.0? .? This project trial produced the first prototype from 1995 (power 2.5kW, after velocity ratio I=32), with some factory and mine cooperation, has one after another designed following several kind of different powers, the different velocity ratio reduction gear.(1) electrically operated on rollers gate uses the reduction gear, power 550W, velocity ratio I=26, is united as one body with the electrical machinery.sion quality. (2) mixer uses the reduction gear, power 370W, velocity ratio I=17.(3) some military goods use two kind of reduction gears, one kind of power 370W, velocity ratio I=23.5; Another kind of power 370W, velocity ratio I=103 two level of transmission reduction gear.(4) steel mill large package rotary abutment reduction gear, power 7.5kw, velocity ratio I=64.(5) steel mill table reduction gear, power 7.5kw, transmission I=11. In this patent foundation, has developed one kind of new ultra-large reduction gear, the power may reach 1000kw, at present is developing subminiature (outlook size for a millimeter level) miniature reduction gear. Graduation design task First, a design Monorail Driver Design reducer Second, the design of the original data 1 Monorail drive reducer Power Rating: 7.5 KW; 2 Monorail reducer drive the total transmission ratio: 15 around; 3 Monorail reducer drive car driven by the side of the output shaft from the race distance of not more than 200 mm; 4 Monorail reducer drive the total length of less than 420 mm, the width is not more than 450 mm and the total height of not more than 690 mm; Third, the equipment and the working environment This can be used to mine underground, open-air, dust, humidity, air quality, bad comparison bad work environment, and the operational requirements of a safe space. Fourth, the design requirements To meet the application requirements under the premise that the minimum cost of manufacturing. From the following aspects considered; (L) to streamline the shape of each parts, machinery simple structure; ??? (2) merge the functions of spare parts, reducing the types or quantities of spare parts; ??? (3) Application of the new structure, new technology, new materials, product reliability; ??? (4) decomposition components, its assembly, the assembly of the most simple structure; ??? (5) similar to parts of the division; ??? (6) standards for similar products by product serial number sequence analysis; ??? (7) The realization of the common parts of the product and standardization. ??? (8) assembly equipment design a map (0), the Six Parts (3), the design specification of a (not less than 30,000 words), and the design of technical and economic analysis. 中文譯文 一、 什么是減速器 減速器是一種動力傳達機構，利用齒輪的速度轉換器，將馬達的回轉數減速到所要的回轉數，并得到較大轉矩的機構。 1、減速器的作用 1）降速同時提高輸出扭矩，扭矩輸出比例按電機輸出乘減速比，但要注意不能超出減速器額定扭矩。 2） 減速同時降低了負載的慣量，慣量的減少為減速比的平方。大家可以看一下一般電機都有一個慣量數值。 2、減速器的種類 一般的減速器有斜齒輪減速器(包括平行軸斜齒輪減速器、蝸輪減速器、錐齒輪減速器等等)、行星齒輪減速器、擺線針輪減速器、蝸輪蝸桿減速器、行星摩擦式機械無級變速機等等。 3、常見減速器 1） 蝸輪蝸桿減速器的主要特點是具有反向自鎖功能，可以有較大的減速比，輸入軸和輸出軸不在同一軸線上，也不在同一平面上。但是一般體積較大，傳動效率不高，精度不高。 2） 諧波減速器的諧波傳動是利用柔性元件可控的彈性變形來傳遞運動和動力的，體積不大、精度很高，但缺點是柔輪壽命有限、不耐沖擊，剛性與金屬件相比較差。輸入轉速不能太高。 3） 行星減速器其優點是結構比較緊湊，回程間隙小、精度較高，使用壽命很長，額定輸出扭矩可以做的很大。但價格略貴一、對裝配前零件的要求 ： 1.滾動軸承用汽油清洗，其他零件用煤油清洗。所有零件和箱體內不許有任何雜質存在　。箱體內壁和齒輪（蝸輪）等未加工表面先后涂兩次不被機油侵蝕的耐油漆，箱體外表　面先后涂底漆和顏色油漆（按主機要求配色）。 2.零件配合面洗凈后涂以潤滑油 二、安裝和調整的要求　 1.滾動軸承的安裝　　滾動軸承安裝時軸承內圈應緊貼軸肩，要求縫隙不得通過0.05mm 厚的塞尺。 2.軸承軸向游隙　　對游隙不可調整的軸承（如深溝球軸承），其軸向游隙為0.25~0.4mm；對游隙可調整　　的軸承軸向游隙數值見表。點擊查看圓錐滾子軸承軸向游隙；角接觸球軸承軸向游隙　 3.齒輪（蝸輪）嚙合的齒側間隙　　可用塞尺或壓鉛法。即將鉛絲放在齒槽上，然后轉動齒輪而壓扁鉛絲，測量兩齒側被　　壓扁鉛絲厚度之和即為齒側的大小?！? 4.齒面接觸斑點圓柱齒輪齒面接觸斑點2-10-4；圓錐齒輪齒面接觸斑點2-11-4；蝸桿傳動接觸斑點2-12-4 三、密封要求　 1.箱體剖分面之間不允許填任何墊片，但可以涂密封膠或水玻璃以保證密封；　 2.裝配時，在擰緊箱體螺栓前，應使用0.05mm的塞尺檢查箱蓋和箱座結合面之間的密封性；　 3.軸伸密封處應涂以潤滑脂。各密封裝置應嚴格按要求安裝 四、潤滑要求　 1.合理確定潤滑油和潤滑脂類型和牌號　 2.軸承脂潤滑時，潤滑脂的填充量一般為可加脂空間的1/2~2/3?！? 3.潤滑油應定期更換，新減速器第一次使用時，運轉7~14天后換油，以后可以根據情況每隔3~6個月?lián)Q一次油。 五、試驗要求　 1.空載運轉：在額定轉速下正、反運轉1~2小時；　 2.負荷試驗：在額定轉速、額定負荷下運轉，至油溫平衡為止?！　X輪減速器，要求油池溫升不超過35oC,軸承溫升不超過40oC；　　對蝸桿減速器，要求油池溫升不超過60oC,軸承溫升不超過50oC；　 3.全部試驗過程中，要求運轉平穩，噪聲小，聯接固定處不松動，各密封、結合處不 六、包裝和運輸要求　 1.外伸軸及其附件應涂油包裝；　 2.搬運、起吊時不得使用吊環螺釘及吊耳以上技術要求不一定全部列出，有時還需另增項目，主要由設計的具體要求而定。 七、技術要求　 1.裝配前，所有零件用煤油清洗，滾動軸承用汽油清洗，不許有任何　　雜物存在。內壁涂上不被機油腐蝕的涂料兩次；　 2.嚙合側隙用鉛絲檢驗不小于0.16mm，鉛絲不得大于最小側隙的4倍；　 3.用涂色法檢驗斑點。按齒高接觸點不小于40%；按齒長接觸斑點不　　小于50%。必要時可用研磨或刮后研磨以便改善接觸情況；　 4.應調整軸承軸向間隙：φ40為0.05--0.1mm,φ55為0.08--0.15mm;　 5.檢驗減速器剖分面、各接觸面及密封處，均不許漏油。剖分面允許　　涂以密封油漆或水玻璃，不允許使用任何填料；　 6.機座內裝N100潤滑油至規定高度。 八、下面我介紹我國減速器的發展現狀 （一）、國內的減速器多以齒輪傳動、蝸桿傳動為主，但普遍存在著功率與重量比小，或者傳動比大而機械效率過低的問題。另外，材料品質和工藝水平上還有許多弱點，特別是大型的減速器問題更突出，使用壽命不長。國內使用的大型減速器（500kw以上），多從國外（如丹麥、德國等）進口。60年代開始生產的少齒差傳動、擺線針輪傳動、諧波傳動等減速器具有傳動比大，體積小、機械效率高等優點?。但受其傳動的理論的限制，不能傳遞過大的功率，功率一般都要小于40kw。由于在傳動的理論上、工藝水平和材料品質方面沒有突破，因此，沒能從根本上解決傳遞功率大、傳動比大、體積小、重量輕、機械效率高等這些基本要求