購買設計請充值后下載，，資源目錄下的文件所見即所得，都可以點開預覽，，資料完整，充值下載可得到資源目錄里的所有文件。。?！咀ⅰ浚篸wg后綴為CAD圖紙，doc,docx為WORD文檔，原稿無水印，可編輯。。。具體請見文件預覽，有不明白之處，可咨詢QQ:12401814
附 錄A
A. multi-purpose vehicle chassis dynamometer
With the rapid development of the automotive industry, traffic accidents and environmental pollution on the growing threat to human life, thus increasing the importance of vehicle detection technology stand out a variety of testing equipment have emerged. As a large-scale laboratory equipment, automobile chassis dynamometer can simulate vehicle road test a variety of conditions, the completion of the car's economy test, power test, evaluation and analysis of emissions performance, reliability test and drive the car on the special test . It is in the automotive testing research, product development and quality testing new cars and the car is essential. Use complete chassis dynamometer test and the type of vehicle quality inspection and road test compared with the usual test speed, high precision, low cost, data stability, comparability and good.
In view of chassis dynamometers these advantages, many domestic manufacturers have developed a series of dynamometer products, these products are mainly used to detect the following auto axle load 10 t chassis power output, the maximum absorption power of 150 kW. Test items mainly: chassis power output, the driving force, speed, acceleration, glide performance and the accuracy of the speedometer and odometer, and so on.
But domestic dynamometer products there are many imperfections, must be resolved. For example: car in different conditions, different load and other conditions, the dynamic performance can not be achieved continuous measurement and control system, control method is relatively backward. This article is for these deficiencies, the control system, control method has been improved to achieve the different conditions and different load conditions, the car's dynamic performance for accurate and reliable continuous measurement and continuous measurement of emissions to increase functionality. In addition, the light of foreign advanced technology and experience, the use of computer technology for vehicle-related transmission loss, rolling resistance, altitude, temperature and other parameters of simulation and correction.
Multi-purpose vehicle chassis dynamometer (hereinafter referred to as dynamometer) is a new chassis dynamometer. Aircraft measurement and control system is the key to achieve its power equipment.
Dynamometer testing computer control system to control the use of high performance industrial control computer, the entire control system including computer, monitor, keyboard, mouse, printers, input and output terminal blocks, multi-PC bus interface card, SCR and its control circuit, all components have been installed in the 1.8 m high of the standard 19-inch industrial control cabinet. Dynamometer control system coupled with the mechanical part of the (bench) constitute the entire dynamometer. Bench control system by the pressure sensor, speed sensor, pneumatic lift, and eddy current machines and other equipment to complete the dynamometer measurement and control.
PC bus interface board is a multi-computer interfaces and measurement equipment, control channel, on-site analog signal amplification and analog-digital conversion, digital signal measurement done by it, the interface card can also control multiple actuator movements, other The card also provides a counter for frequency measurement of the interface.
Wheel drive car in the bench rotating drum, drum rotation by the optical pulse output of the decoder, access multi-function card counter, measuring speed and distance traveled. Car driving in the bench, the driving force can drum machine by the eddy current coupling the pressure sensor, the input channel signal sent to the computer, combined with the speed signal measurable car's dynamic performance. In the actual measurement process, the measured speed signal and set the speed comparison, according to a certain algorithm to adjust bias resistance (eddy current excitation current), so that speed can be stabilized at a given value, complete constant speed under the conditions of the various data measurements.
Dynamometer applications from the measurement control program, the login program and database service program structure, program design using advanced C / S (Client / Server) design. Measurement control program and the login program is a client application, they exchange data with the database is a database service procedures are completed, the database structure is transparent to users, to facilitate the system and other motor vehicle testing equipment or manage network connections. User login process is complete the basic information on the vehicle, the initial set of test items; measurement control program is the core of the system program, its main function is to complete the measurement and control hardware signals, according to testing requirements set by the login program to complete the detection task, the program also provides another parameter setting, test results query, print and other auxiliary functions.
Eddy current machines, also known as eddy current dynamometer, is based on the eddy current (also known physics Foucault current) work equipment. It consists of two parts, the stator and rotor. The stator frame and the stator part including the exciting coil mounted on top. The stator frame around the hole, the excitation coils installed in the hole. The framework of the central part of the stator hub, with two bearing supports the rotor shaft. Including the rotor shaft and the rotor part fixed on the axis of the two rotors, two rotors are located at both ends of the stator part of the rotor shaft can be driven by external forces and free rotation. The inside of the rotor and the stator end face to maintain a small gap, the gap is called electromagnetic air gap. The inner side of the rotor is a very smooth surface, eddy current is generated in the smooth plane.
Eddy current machine field winding access current, flux through the stator, eddy current ring, the air gap, rotor constitute a closed magnetic circuit. When the car wheel and drive roller rotates the rotor eddy current machines, due to changes in magnetic flux density of the surface of the rotor eddy current, the eddy current and magnetic field interact to produce the reverse braking torque, the stator swing around the spindle axis. Pass through the leverage of the brake torque to the pressure sensor, pressure sensor gives the corresponding electrical signals, processed by the calculation, the instantaneous power can be drawn vehicle parameters. Adjust the excitation current size, you can change the eddy current machine braking torque, with a corresponding change in vehicle speed, changing the excitation current and speed the formation of a closed loop, constant speed or constant force and, ultimately, the power measurement.
Eddy current machine has a maximum speed and load range. In addition, its small size, low cost, more suitable for control automation. AC motors (induction motors) with a minimum speed (800 ~ 1500r/min) and load range, less stable, with a little hard to load features. DC Braking device with high performance, easy operation, stable working conditions, the transition easy and smooth, but its test-bed high cost, low-speed braking torque is small, thus limiting the application.
This system was chosen as the eddy current unit load device, because of its external features and cost, reliability, accuracy decision.
Currently, the majority of domestic water vortex machine dynamometer, eddy current machine has a small amount of several major water-cooled, easy-to leakage, resulting in corrosion of the bearing parts, easy to magnetic flux leakage, constant speed control accuracy, and the volume weight, need a water cooling system and lubrication system inside the vortex, very easy to use, in northern China, especially in winter does not apply. More importantly, domestic water eddy current machine for almost all the engine power measurement of high-speed power absorption unit (maximum power absorption range of 1500 ~ 4000 r / min), does not apply to vehicle chassis dynamometer, which is the maximum power absorption range of 500 ~ 1000 r / min. The international production of this special low speed, high torque eddy current machine only company in Spain and France TELMA FRENELSA company, their product mix to air-cooled.
As the dynamometer torque and power measurement of the speed and load requirements to a large extent, considering cost, reliability, accuracy in the case we have chosen FRENELSA's F16-160-type air-cooled eddy current machine group 16, the absorption maximum torque speed of 750 r / min, vortex machine voltage is DC96V, current is 35A, the maximum absorption torque of 160 kg. The vortex machine constant high precision, volume weight, simple structure, easy to operate, do not need cooling water, and built-in thermocouple 160 ℃, can overheat when the automatic power-off, to avoid eddy current machine was burned.
Eddy current machine is a constant speed control accuracy of the dynamometer test one of the key factors, most of the domestic dynamometer does not really solve the problem. According to standard, constant accuracy should reach ± ??2 km / h (such as China GB86-94), but because of large mechanical movement of the system inertia, and inertia of different models is different from the same time, there are dead out of control, non-linear, lag reaction speed feedback in the difficulty of making the design of constant speed control has become one of the key.
Currently, we are to be addressed in several ways, one direct drive as far as possible, reducing the dead zone and hysteresis control response, and digital speed control and adaptive control to solve the different moment of inertia effects. In addition, two large closed-loop speed and current use of different sampling frequency in order to effectively control the vortex dynamics and the feedback current machine. Test proved to be stable to ± 0.5 km / h, is a standard 1 / 4.
Control process is as follows: the car began to accelerate, due to the speed difference between running speed and a larger set, using the experience of the control algorithm that is according to certain rules and gradually increase the resistance; Once the vehicle speed close to the set speed, adaptive control work. Because in the start-up phase, the running speed as soon as possible close to the set speed is the primary goal, and the last way in which speed is not stable in the set under consideration, the experience of control is simple and works well in control. The speed close to the set speed, the speed and stability the only objective, experience, control can not do anything at this time. The actual vehicle operating conditions is very complex, and the speed variation is difficult to predict, and thus the control of any form pre-set parameters are not always achieve the best control action, the effect of operating conditions and with the pros and cons of changing. Adaptive control is to adapt to similar conditions and developed, it can under the conditions and adjust the control parameters in order to achieve real-time optimal control.
Car in idle state, the different load conditions, different speeds and different road conditions in the case of the emissions are different, the measured data for vehicle maintenance is important, but more important is to determine whether emissions from vehicles qualified to provide a basis for the environmental protection departments to provide accurate detection and rich data material. The dynamometer with the exhaust gas analyzer can be in different working conditions under the conditions of vehicle emissions testing, testing standards fully in line with the introduction of a new national standard (GB14761-1999).
The following chassis dynamometer at constant speed, for example, analysis of measurement results.
Experimental conditions: the initial speed of 60 km / h, the termination rate of 80 km / h, speed step of 5 km, constant and stable point 5. Test vehicle for the Santana sedan.
In constant speed mode with exhaust gas analyzer, we carried out the engine output power, wheel torque and power output, transmission loss of power, CO, CO2, HC, O2, eight parameters were measured, and the speed, power, torque for real-time monitoring.
In this experiment, the wheel and experience the power output values ??match, the engine output power wheel power output of power and transmission losses and. Maximum power output of the corresponding wheel speed of 75 km / h. Transmission loss of power to test the vehicle drive power is an important parameter passing, it is directly related to the car's dynamic performance.
Multi-function chassis dynamometer is a motor transport and maintenance industry, comprehensive performance inspection stations, environmental protection, transportation (cars scrapped in the future will be according to their dynamic performance and emissions performance may be) and other necessary test equipment industry, with broad market prospects. By computer-controlled eddy current dynamometer load to achieve resistance simulation, different conditions can be measured vehicle dynamic performance and environmental performance (emissions performance), and has correction, the actual measurement data closer to the car when driving data. The dynamometer speed control through the adaptive control algorithm to improve the car's constant stability and achieve a dynamic performance and environmental performance of continuous measurement.
附 錄B
多功能汽車底盤測功機
隨著汽車工業的迅猛發展，交通事故及環境污染對人類生命的威脅越來越大，因而汽車檢測技術的重要性日益突出出來，各種檢測設備也應運而生。作為大型實驗設備，汽車底盤測功機可以模擬汽車道路試驗的各種工況，完成汽車的經濟性試驗、動力性試驗、排放性能評價與分析、可靠性試驗以及與汽車傳動系統有關的專項試驗。它在汽車試驗研究、產品開發和新車及在用車質量檢測中是不可或缺的。使用汽車底盤測功機完成汽車試驗及各類型的質量檢測與通常的道路試驗相比具有試驗速度快、精度高、費用低、數據穩定、可比性好等優點。
鑒于汽車底盤測功機的以上優點，國內許多廠家先后研制開發了一系列測功機產品，這些產品主要用于檢測軸重10 t以下的汽車底盤輸出功率，最大吸收功率為150 kW。檢測項目主要是：汽車底盤的輸出功率、驅動力、車速、加速性能、滑行性能、以及車速表和里程表的準確性等等。
但是國內測功機產品還有許多不完善的地方，亟待解決。例如：汽車在不同工況、不同負載等狀態下，其動力性能不能實現連續測量，控制系統、控制方法比較落后。本文正是針對這些不足，在控制系統、控制方法上進行了改進，實現了不同工況、不同負載的狀態下，對汽車動力性能進行準確可靠的連續測量，并且增加了排放的連續測量功能。此外，參照國外先進技術及經驗，利用計算機技術對汽車有關傳動損耗、滾動阻力、海拔高度、氣溫等參數進行模擬和修正。
多功能汽車底盤測功機（以下簡稱測功機）是一種新型底盤測功機。該機的測量和控制系統是實現其強大功能的關鍵設備。
測功機檢測控制系統中的控制微機采用高性能的工業控制計算機，整個測控系統包括計算機、顯示器、鍵盤、鼠標、打印機，輸入輸出端子板，多功能PC總線接口卡、可控硅及其控制電路，所有部件全部安裝在1．8 m高的標準19寸工業控制柜中。測控系統加上測功機的機械部分（臺架）構成了整個測功機。測控系統通過臺架上的壓力傳感器、速度傳感器、氣動舉升機和電渦流機等裝置，完成對測功機的測量和控制。
多功能PC總線接口板是計算機和測量控制通道的接口設備，現場模擬信號的放大和模數轉換、開關量信號的測量都由它完成，該接口卡還能控制多個執行機構的動作，另外該卡還提供了用于頻率測量的計數器接口。
在臺架上汽車驅動輪帶動滾筒轉動，滾筒轉動經光電解碼器產生脈沖輸出，接入多功能卡的計數器，測量速度和行駛距離。汽車在臺架上行駛時，其驅動能對滾筒的作用力經電渦流機耦合在壓力傳感器上，由輸入通道將信號送入計算機，與速度信號結合可測量汽車的動力性能。在實際測量過程中，實測的速度信號與設定速度比較，根據偏差按一定的算法調整阻力（電渦流機勵磁電流），使車速能穩定在給定值，完成恒速條件下各種數據的測量。
測功機的應用軟件由測量控制程序、登錄程序和數據庫服務程序構成，程序設計采用先進的C/S（客戶/服務器）設計方法。測量控制程序和登錄程序是客戶端程序，它們與數據庫的數據交換是通過數據庫服務程序完成，數據庫結構對用戶是透明的，方便本系統與其他機動車檢測設備或管理網絡連接。登錄程序完成用戶對車輛的基本信息、檢測項目的初始設定；測量控制程序是該系統的核心程序，其主要功能是完成對硬件信號的測量和控制、按登錄程序設定的檢測要求完成各項檢測任務，另外該程序還提供參數設定、檢測結果查詢、打印等輔助功能。
電渦流機又稱電渦流測功器，是基于渦流電流（物理學上也稱傅科電流）進行工作的設備。它由定子和轉子兩部分組成。定子部分包括定子架和裝在上面的勵磁線圈。定子框架周?chē)锌祝瑒?lì)磁線圈裝在孔內。定子框架中心部分輪轂，借助兩個滾動軸承支撐在轉子軸上。轉子部分包括轉子軸和固定在該軸上的兩個轉子，兩個轉子分別位于定子部分的兩端，轉子軸可以被外力帶動而自由轉動。轉子的內側端面與定子的端面保持很小的間隙，該間隙電磁學上稱為氣隙。該轉子的內側面是十分光滑的平面，渦流電流就產生在這個光滑平面上。
電渦流機的勵磁繞組通入電流時，磁通經定子、渦流環、氣隙、轉子構成閉合磁路。當汽車驅動輪帶動滾筒及電渦流機轉子旋轉時，由于磁通密度發生變化使轉子表面產生渦流電流，該渦流電流與磁場相互作用，產生反向制動力矩，使定子繞主軸軸線擺動。該制動力矩通過杠桿傳遞給壓力傳感器，由壓力傳感器給出相應的電信號，經計算處理后，可得出汽車瞬時的動力參數。調節勵磁電流大小，即可改變電渦流機的制動力矩，同時相應改變汽車車速，不斷變化的勵磁電流與車速形成閉合環，并最終實現恒速或恒力下的功率測量。
電渦流機具有最大的速度和載荷范圍。此外它體積小，造價低，更適合于操縱自動化。交流電機（異步電機）具有最小的速度（800～1500r/min）和載荷范圍，穩定性較差，小負荷具有很硬的特性。直流電機制動裝置具有很高的使用性能，操作方便，工況穩定，過渡簡易且平穩，但它的試驗臺造價高，低速制動扭矩小，因而限制了應用。
本系統之所以選擇電渦流機作為加載裝置，是由于它的外特性及造價、可靠性、測量精度決定的。
目前，國產渦流機大部分為水力測功機，少量幾種電渦流機也主要為水冷式的，易漏水，導致軸承機件銹蝕，容易漏磁，恒速控制精度差，且體積重量大，需要一套供水冷卻循環系統及渦流機內部潤滑系統，使用很不方便，在我國北方，冬季尤為不適用。更為重要的是，國產水力電渦流機幾乎全部用于發動機功率測量的高轉速功率吸收裝置（最大功率吸收范圍1500～4000 r/min），不適用于汽車底盤測功，后者最大功率吸收范圍為500～1000 r/min。國際上專門生產這種低轉速，大扭矩電渦流機只有西班牙的FRENELSA公司和法國的TELMA公司，他們的產品結構為風冷式。
由于測功機的扭矩和功率測量對速度和載荷范圍要求要大，在考慮造價、可靠性、測量精度的情況下我們選擇了FRENELSA公司的F16—160型風冷16組電渦流機，其最大扭矩吸收轉速為750 r/min，渦流機電壓為DC96V，電流為35A，最大吸收扭矩為160 kg。該渦流機恒速精度高，體積重量小，結構簡單，操作方便，勿需冷卻水，且內置160℃熱電偶，可在過熱時自動斷電，避免渦流機被燒壞。
電渦流機的恒速控制是測功機測試精度的關鍵因素之一，國內大部分測功機未真正解決好這一問題。按標準規定，恒速精度應達到±2 km/h（如中國GB86—94），但由于機械系統運動慣量較大，且不同車型慣量不同，同時，存在失控死區、非線性、滯后反應等調速反饋方面的難度，使得恒速控制成為設計中的重點之一。
目前，我們通過幾種途徑予以解決，一是盡量采用直接傳動，減小失控死區及滯后反應，同時采用數字調速和自適應控制等解決不同轉動慣量的影響。此外，大轉速及電流兩個閉環中采用不同的采樣頻率以便有效的控制渦流機動態及反饋電流。測試證明可以穩定達到±0．5 km/h，是標準的1/4。
控制過程如下：汽車在開始加速時，由于運行速度與設定速度相差較大，采用經驗控制算法即按一定的規律逐步增加阻力；一旦汽車運行速度接近設定速度，自適應控制開始工作。因?yàn)樵趩?dòng)階段，使運行速度盡快接近設定速度是首要目的，而最后以何種方式穩定在設定速度則不在考慮之內，經驗控制是簡單易行且效果很好的控制方式。在運行速度接近設定速度之后，速度的穩定成為唯一目的，此時經驗控制就無能為力了。汽車的實際運行工況十分復雜，其速度變化規律難以預測，因而任何預先設定參數的控制形式都不可能一直發揮最佳控制作用，其效果的優劣隨運行工況而不斷變化。自適應控制正是為適應類似的工況而發展起來的，它能夠根據工況而調整控制參數，以實現實時最佳控制。
汽車在怠速狀態下，不同負載狀態下，不同車速狀態下以及不同路況的情況下的排放都是不同的，測量到這些數據對于汽車維修保養很重要，但更為重要的是為判斷汽車排放是否合格提供依據，為環保檢測部門提供精確而豐富的數據材料。本測功機可以配合尾氣分析儀在不同工況的條件下進行汽車排放的檢測，檢測標準完全符合新出臺的國家標準（GB14761—1999）。
下面以恒速底盤測功為例，分析一下測量結果。
實驗條件：起始速度60 km/h，終止速度80 km/h，速度步長5 km，恒速穩定點為5個。試驗車為桑塔那轎車。
在恒速狀態下配合尾氣分析儀，我們進行了發動機輸出功率、輪輸出扭矩及功率、傳動損耗功率、CO、CO2、HC、O2等8個參數的測量，并對速度、功率、扭矩進行了實時監控。
在本試驗中，輪輸出功率與經驗數值相符，發動機輸出功率為輪輸出功率與傳動損耗功率之和。輪輸出最大功率對應的速度為75 km/h。傳動損耗功率是檢驗汽車驅動功率是否合格的重要參數，它直接關系到汽車的動力性能。
多功能汽車底盤測功機是汽車運輸維修業、綜合性能檢測站、環境保護、交通（今后在用車報廢將按其動力性能及排放性能而定）等行業所必需的測試設備，具有廣闊的市場前景。通過計算機控制電渦流測功器加載實現阻力模擬，可以測量不同的工況下汽車動力性能和環保性能（排放性能），并具有修正功能，測量數據更接近汽車實際行駛時的數據。本測功機通過自適應控制算法控制車速，提高了汽車的恒速穩定性，并且實現了動力性能和環保性能的連續測量。