1937_雷達頻率機械調控機構的設計
1937_雷達頻率機械調控機構的設計,雷達,頻率,機械,調控,機構,設計
單位代碼 0 2 學 號 080105037 分 類 號 TH6 密 級 畢 業 設 計文獻翻譯院 ( 系 ) 名 稱 工 學 院 機 械 系專 業 名 稱 機 械 設 計 制 造 及 其 自 動 化學 生 姓 名 史 杰 指 導 教 師 王 飛2012 年 03 月 18 日黃河科技學院畢業設計(文獻翻譯) 第 1 頁—————————————————————————————1.6 EFFECT OF OPERATING FREQUENCY ON RADARRadars have been operated at frequencies as low as 2 MHz (just above the AM broadcast band) and as high as several hundred GHz (millimeter wave region). More usually, radar frequencies might be from about 5 MHz to over 95 GHz. This is a very large extent of frequencies, so it should be expected that radar technology, capabilities, and applications will vary considerably depending on the frequency range at which a radar operates. Radars at a particular frequency band usually have different capabilities and characteristics than radars in other frequency bands. Generally, long range is easier to achieve at the lower frequencies because it is easier to obtain high-power transmitters and physically large antennas at the lower frequencies. On the other hand, at the higher radar frequencies, it is easier to achieve accurate measurements of range and location because the higher frequencies provide wider bandwidth (which determines range accuracy and range resolution) as well as narrower beam antennas for a given physical size antenna (which determines angle accuracy and angle resolution). In the following, the applications usually found in the various radar bands are briefly indicated. The differences between adjacent bands, however, are seldom sharp in practice, and overlap in characteristics between adjacent bands is likely.HF (3 to 30 MHz). The major use of the HF band for radar (Chapter 20) is to detect targets at long ranges (nominally out to 2000 nmi) by taking advantage of the refraction of HF energy by the ionosphere that lies high above the surface of the earth. Radio amateurs refer to this as short-wave propagation and use it to communicate over long distances. The targets for such HF radars might be aircraft, ships, and ballistic missiles, as well as the echo from the sea surface itself that provides information about the direction and speed of the winds that drive the sea.VHF (30 to 300 MHz). 黃河科技學院畢業設計(文獻翻譯) 第 2 頁—————————————————————————————At the beginning of radar development in the 1930s, radars were in this frequency band because these frequencies represented the frontierof radio technology at that time. It is a good frequency for long range air surveillanceor detection of ballistic missiles. At these frequencies, the reflection coefficient on scattering from the earth’s surface can be very large, especially over water, so the constructive interference between the direct signal and the surface-reflected signal can increase significantly the range of a VHF radar. Sometimes this effect can almost double the radar’s range. However, when there is constructive interference that increases the range, there can be destructive interference that decreases the range due to the deepnulls in the antenna pattern in the elevation plane. Likewise, the destructive interference can result in poor low-altitude coverage. Detection of moving targets in clutter is often better at the lower frequencies when the radar takes advantage of the Doppler frequency shift because doppler ambiguities (that cause blind speeds) are far fewer at low frequencies. VHF radars are not bothered by echoes from rain, but they can be affected by multiple-time-around echoes from meteor ionization and aurora. The radar cross section of aircraft at VHF is generally larger than the radar cross section at higher frequencies. VHF radars frequently cost less compared to radars with the same range performance that operate at higher frequencies.Although there are many attractive advantages of VHF radars for long-range surveillance, they also have some serious limitations. Deep nulls in elevation and poor low-altitude coverage have been mentioned. The available spectral widths assigned to radar at VHF are small so range resolution is often poor. The antenna beamwidths are usually wider than at microwave frequencies, so there is poor resolution and accuracy in angle. The VHF band is crowded with important civilian services such as TV and FM broadcast, further reducing the availability of spectrum space for radar. External noise levels that can enter the radar via the antenna are higher at VHF than at microwave frequencies. Perhaps the chief limitation of operating radars at VHF is the difficulty of obtaining suitable spectrum space at these crowded frequencies.In spite 黃河科技學院畢業設計(文獻翻譯) 第 3 頁—————————————————————————————of its limitations, the VHF air surveillance radar was widely used by the Soviet Union because it was a large country, and the lower cost of VHF radars made them attractive for providing air surveillance over the large expanse of that country.8 They have said they produced a large number of VHF air-surveillance radars—some were of very large size and long range, and most were readily transportable. It is interesting to note that VHF airborne intercept radars were widely used by the Germans in World War II. For example, the Lichtenstein SN-2 airborne radar operated from about 60 to over 100 MHz in various models. Radars at such frequencies were not affected by the countermeasure called chaff (also known as window).UHF (300 to 1000 MHz). Many of the characteristics of radar operating in the VHF region also apply to some extent at UHF. UHF is a good frequency for Airborne Moving Target Indication (AMTI) radar in an Airborne Early Warning Radar (AEW), as discussed in Chapter 3. It is also a good frequency for the operation of long-range radars for the detection and tracking of satellites and ballistic missiles. At the upper portion of this band there can be found long-range shipboard air-surveillance radars and radars (called wind profilers) that measure the speed and direction of the wind.Ground Penetrating Radar (GPR), discussed in Chapter 21, is an example of what is called an ultrawideband (UWB) radar. Its wide signal bandwidth sometimes covers both the VHF and UHF bands. Such a radar’s signal bandwidth might extend, for instance, from 50 to 500 MHz. A wide bandwidth is needed in order to obtain good range resolution. The lower frequencies are needed to allow the propagation of radar energy into the ground. (Even so, the loss in propagating through typical soil is so high that the ranges of a simple mobile GPR might be only a few meters.) Such ranges are suitable for locating buried power lines and pipe lines, as well as buried objects. If a radar is to see targets located on the surface but within foliage, similar frequencies are needed as for the GPR.L band (1.0 to 2.0 GHz). This is the preferred frequency band for the operation of 黃河科技學院畢業設計(文獻翻譯) 第 4 頁—————————————————————————————long-range (out to 200 nmi) air-surveillance radars. The Air Route Surveillance Radar (ARSR) used for long range air-traffic control is a good example. As one goes up in frequency, the effect of rain on performance begins to become significant, so the radar designer might have to worry about reducing the effect of rain at L-band and higher frequencies. This frequency band has also been attractive for the long-range detection of satellites and defense against intercontinental ballistic missiles.S band (2.0 to 4.0 GHz). The Airport Surveillance Radar (ASR) that monitors air traffic within the region of an airport is at S band. Its range is typically 50 to 60nmi. If a 3D radar is wanted (one that determines range, azimuth angle, and elevation angle), it can be achieved at S band.It was said previously that long-range surveillance is better performed at low frequencies and the accurate measurement of target location is better performed at high frequencies. If only a single radar operating within a single frequency band can be used, then S band is a good compromise. It is also sometimes acceptable to use C band as the choice for a radar that performs both functions. The AWACS airborne air-surveillance radar also operates at S band. Usually, most radar applications are best operated in a particular frequency band at which the radar’s performance is optimum. However, in the example of airborne air-surveillance radars, AWACS is found at S band and the U.S. Navy’s E2 AEW radar at UHF. In spite of such a difference in frequency, it has been said that both radars have comparable performance. 9 (This is an exception to the observation about there being an optimum frequency band for each application.)The Nexrad weather radar operates at S band. It is a good frequency for the observation of weather because a lower frequency would produce a much weaker radar echo signal from rain (since the radar echo from rain varies as the fourth power of the frequency), and a higher frequency would produce attenuation of the signal as it propagates through the rain and would not allow an accurate measurement of rainfall rate. There are weather radars at higher frequencies, but these are usually of shorter 黃河科技學院畢業設計(文獻翻譯) 第 5 頁—————————————————————————————range than Nexrad and might be used for a more specific weather radar application than the accurate meteorological measurements provided by Nexrad.C band (4.0 to 8.0 GHz). This band lies between S and X bands and has properties in between the two. Often, either S or X band might be preferred to the use of C band, although there have been important applications in the past for C band.X band (8 to 12.0 GHz). This is a relatively popular radar band for military applications. It is widely used in military airborne radars for performing the roles of interceptor, fighter, and attack (of ground targets), as discussed in Chapter 5. It is also popular for imaging radars based on SAR and ISAR. X band is a suitable frequency for civil marine radars, airborne weather avoidance radar, airborne doppler navigation radars, and the police speed meter. Missile guidance systems are sometimes at X band. Radars at X band are generally of a convenient size and are, therefore, of interest for applications where mobility and light weight are important and very long range is not a major requirement. The relatively wide range of frequencies available at X band and the ability to obtain narrow beamwidths with relatively small antennas in this band are important considerations for high-resolution applications. Because of the high fre-quency of X band, rain can sometimes be a serious factor in reducing the performance of X-band systems.Ku, K, and Ka Bands (12.0 to 40 GHz). As one goes to higher radar frequency, the physical size of antennas decrease, and in general, it is more difficult to generate large transmitter power. Thus, the range performance of radars at frequencies above X band is generally less than that of X band. Military airborne radars are found at Ku band as well as at X band. These frequency bands are attractive when a radar of smaller size has to be used for an application not requiring long range. The Airport Surface Detection Equipment (ASDE) generally found on top of the control tower at major 黃河科技學院畢業設計(文獻翻譯) 第 6 頁—————————————————————————————airports has been at Ku band, primarily because of its better resolution than X band. In the original K band, there is a water-vapor absorption line at 22.2 GHz, which causes attenuation that can be a serious problem in some applications. This was discovered after the development of K-band radars began during World War II, which is why both Ku and Ka bands were later introduced. The radar echo from rain can limit the capability of radars at these frequencies.Millimeter Wave Radar. Although this frequency region is of large extent, most of the interest in millimeter wave radar has been in the vicinity of 94 GHz where there is a minimum (called a window) in the atmospheric attenuation. (A window is a region of low attenuation relative to adjacent frequencies. The window at 94 GHz is about as wide as the entire microwave spectrum.) As mentioned previously, for radar purposes, the millimeter wave region, in practice, generally starts at 40 GHz or even at higher frequencies. The technology of millimeter wave radars and the propagation effects of the environment are not only different from microwave radars, but they are usually much more restricting. Unlike what is experienced at microwaves, the millimeter radar signal can be highly attenuated even when propagating in the clear atmosphere. Attenuation varies over the millimeter wave region. The attenuation in the 94 GHz window is actually higher than the attenuation of the atmospheric water-vapor absorption line at 22.2 GHz. The one-way attenuation in the oxygen absorption line at 60 GHz is about 12 dB per km, which essentially precludes its application. Attenuation in rain can also be a limitation in the millimeter wave region.Interest in millimeter radar has been mainly because of its challenges as a frontierto be explored and put to productive use. Its good features are that it is a great place foremploying wide bandwidth signals (there is plenty of spectrum space); radars can havehigh range-resolution and narrow beamwidths with small antennas; hostile electroniccountermeasures to military radars are difficult to employ; and it is easier to have a military radar with low probability of intercept at these frequencies than at 黃河科技學院畢業設計(文獻翻譯) 第 7 頁—————————————————————————————lower frequencies. In the past, millimeter wave transmitters were not capable of an average power more than a few hundred watts—and were usually much less. Advances in gyrotrons (Chapter 10) can produce average power many orders of magnitude greater than more conventional millimeter-wave power sources. Thus, availability of high power is not a limitation as it once was.Laser Radar. Lasers can produce usable power at optical frequencies and in the infrared region of the spectrum. They can utilize wide bandwidth (very short pulses) and can have very narrow beamwidths. Antenna apertures, however, are much smaller than at microwaves. Attenuation in the atmosphere and rain is very high, and performance in bad weather is quite limited. Receiver noise is determined by quantum effects rather than thermal noise. For several reasons, laser radar has had only limited application.黃河科技學院畢業設計(文獻翻譯) 第 8 頁—————————————————————————————1.6 工作頻率對雷達的影響雷達已在低至 3hz (剛好高于 AM 廣播頻段)的頻率上工作過,也在高至數百 GHz(毫米波段)頻率上工作過。雷達更常用的頻帶可能為 5 陽也~95GHz 以上,這是一個巨大的頻率范圍,所以應該可以預期的是雷達技術、性能及應用會顯著依賴于雷達工作的頻段而變化。不同頻段的雷達通常具有不同的性能和特性。→般,在低頻段易于獲得遠程性能,因?yàn)樵诘皖l易于獲得大功率發射機和物理上巨大的天線。另一方面,在更高的雷達頻率上,容易完成距離和位置的精確測量,因?yàn)楦叩念l率能提供更寬的帶寬(它決定距離精度和分辨率),以及在給定夭線物理尺寸時更窄的波束(它決定角精度和角分辨率)。下面簡要介紹不同波段的雷達應用。然而相鄰波段的區別在實踐中沒有顯著差別,在特性上可能會有重疊。高頻(HF. 3—30MHz) HF 頻段的主要用途是被雷達用來探測遠程目標(標稱可達到 2000n mile) ,方法是利用高頻電磁波能量被遠離地表的電離層折射的特性。無線電愛好者稱這為短波傳播并用它來在遠距離上通信。 HF 雷達的目標可能是飛機、艦船和彈道導彈,以及來自海面本身的回波(可提供驅動海面的風向及風速的信息)。甚高頻(VHF30—300MHZ)20 世紀 30 年代開發的大多數早期雷達都工作在該頻段,因?yàn)樵诋?dāng)時這些頻率代表無線電技術的前沿。它對遠程空中監視和探測彈道導彈是很好的頻率。在這些頻率上,地球表面特別是水面散射的反射系數會非常大,所以直達信號和面反射信號之間的相長干涉會顯著增大 VHF 雷達的作用距離。然而,當有這種效應使作用距離翻倍時,會有伴隨而來的相消干涉減少作用距離,這是由于在某些仰角上,天線方向圖有深的零點。同樣,相消干涉會導致低空上差的覆蓋。雷達利用多普勒頻移探測雜波中的動目標時在低頻上經常會更好,因?yàn)槎嗥绽漳:?導致盲速)在低頻段要少得多。 VHF 雷達不受雨雜波困擾,但受來自流星的電離和極光的多次時間折疊回波的影響。在 VHF 頻段,飛機的雷達截面積一般比在更高的頻率上大。 VHF 雷達在獲得同樣的距離性能時比工作在更高頻段上的雷達花費要少。盡管甚高頻雷達對遠程監視有許多誘人的優點,但也有很多嚴重的局限。俯仰上的深零點及差的低空覆蓋之前已經提到了。分配給 黃河科技學院畢業設計(文獻翻譯) 第 9 頁—————————————————————————————VHF 雷達的可用頻譜寬度很窄,因此距離分辨率經常很差。天線波束寬度通常比微波頻段的寬,因此角精度和分辨率也差。 VHF 頻段中擁擠著許多重要的民用服務,如電視和調頻廣播,這進一步減少了雷達可用的頻譜空間。通過天線進入雷達的外部噪聲電平在 VHF 頻段比微波頻段高。工作在 VHF 頻段,雷達的主要局限可能是在這個擁擠的頻段中獲得合適頻譜空間的困難。盡管有局限,VHF 對空監視雷達在蘇聯曾廣泛使用,因?yàn)樘K聯國土廣大,而 VHF 雷達的低廉,對提供疆域這么廣闊國家的空中監視很有吸引力[8] 。據說蘇聯生產了大量的 VHF 對空監視雷達一一一些有著非常巨大的只寸和遠的作用距離,但多數是可容易運輸?shù)?。有意思的?VHF 機載攔截雷達曾在第二次世界大戰中被德國廣泛使用。例如, Lichtenstein SN-2 機載雷達在不同型號中工作在 60~100MHz 上。在這些頻率上的雷達不受稱為輔條(也稱為窗口)的對抗措施的影響。超高頻(UHF.300MHZ—1GHZ)工作在甚高頻雷達的許多特點在一定程度上也適合于超高頻。 UHF 特別適合于機載預警雷達系統 (AEW) 中的機載 AMTI (動目標檢測)雷達(參見第 3 章),也適于探測和跟蹤衛星和彈道導彈的遠程雷達。在這個波段的上段可找到遠程艦載對空監視雷達和測量風速及風向的雷達(稱為風靡線雷達)。地面穿透雷達 CGPR) ,是所謂超寬帶 (UWB) 雷達的例子,參見第 21 章。它寬的信號帶寬有時同時覆蓋 VHF 和 UHF 波段。這種雷達的信號帶寬可能從 50MHz 延伸到 500MHz。寬的帶寬對獲得好的距離分辨率是需要的。低頻率對允許雷達能量穿透地面?zhèn)鞑ナ切枰?盡管如此,在典型土壤中傳播衰減迅速,因而簡單的機動 GPR 作用距離可能僅有幾米)。這個距離適合定位掩埋在地 F 的電線、管線和其他物體。如果雷達要發現位于地表但被樹木遮蓋的目標,也需要同 GPR 所用類似的頻段。Ku,K 和 Ka 波段(14.0—40.0GHZ)在更高的雷達頻率上,天線物理尺寸減小,一般更難產生大的發射機功率。因此, X 波段之上頻段的雷達的距離性能一般不如 X 波段的雷達。軍用機載雷達有 X 波段的,也有 Ku 波段的。對必須要有小的尺寸而不需要遠距離的雷黃河科技學院畢業設計(文獻翻譯) 第 10 頁—————————————————————————————達應用,這些頻段具有吸引力。機場表面探測設備 CASDE) ,通常在大型機場控制塔的頂端可以找到,工作在 Ku 波段,主要因?yàn)樗?X 波段有更好的分辨率。在原先的 K 波段中,在 22.2GHz 處有一條水蒸氣吸收線,這導致的衰減在一些應用中是個嚴重的問題。這個問題當 K 波段雷達在第二次世界大戰期間研制開始以后被發現,這就是后來引入 Ku 和 Ka 波段的原因。雨雜波會限制該波段雷達的性能。毫米波波段盡管這個頻段很寬,多數毫米波雷達感興趣的頻率位于 94GHz 附近,此處的大氣衰減有一個極小值(稱為窗口,是指相對于其附近的頻率衰減小的區域, 94GHz 附近的窗口和整個微波頻段一樣寬)。如上面所提到的,對雷達的目的,毫米波范圍實際上一般從 40GHz 甚至更高的頻率開始。毫米波雷達的技術和環境的傳播效應不僅不同于微波雷達,而且通常有更多的限制。不同于微波波段雷達所經歷的衰減,毫米波雷達信號即使在潔凈的空氣中傳播也會有很大的衰減。衰減在毫米波段是變化的。 94GHz 窗口中的衰減實際上比大氣 22.2GHz處的水蒸氣吸收線還要高。在 60GHz 氧氣吸收線處的單程衰減約為 12 扭曲,基本上排除了雷達在其鄰近頻率的應用。雨的衰減對毫米波波段也是一種限制。對毫米波雷達感興趣的主要原因是因?yàn)樗鳛檠芯亢陀谐晒膽?yīng)用的前沿帶來的挑戰。它的好的特點在于它是采用寬帶寬信號的極好場所(有大量的頻譜空間);雷達可使用小的天線得到高距離分辨率和窄波束:敵方難以對軍用雷達使用電子對抗措施:它使位于這些頻率的軍用雷達比低頻率的雷達有低的被截獲概率。在過去,毫米波發射機平均功率無法超過數百瓦一一通常要低得多?;匦苌系倪M(jìn)展(參見第 10 章)使得可以產生比傳統的毫米波功率源大幾個數量級的平均功率。因此,獲得大功率不再成為限制。激光雷達激光器在頻譜的光學和紅外區可以產生可用的功率。它可使用寬帶寬(極短脈沖)并具有非常窄的波束寬度,而天線孔徑比微波段的小很多。大氣和雨的衰減非常高,因此在惡劣天氣中的性能十分有限。接收機噪聲由量子效應而不是熱黃河科技學院畢業設計(文獻翻譯) 第 11 頁—————————————————————————————噪聲決定。由于幾種原因,激光雷達的應用有限。1.8 雷達過去的一些進展(1)第二次世界大戰之前和第二次世界大戰期間,開發為防空部署在地面、艦船和軍用飛機上的 VHF 雷達。(2) 第二次世界大戰早期微波磁控管的發明和波導技術的應用,以獲得能在微波頻段工作的雷達,從而可使用更小和機動性更強的雷達。(3 )MIT 輻射實驗室在第二次世界大戰期間存在的五年中開發了超過 100 種不同的雷達型號,為微波雷達奠定了基礎。(4) Marcum 的雷達檢測理論。(5) 速調管和行波管放大器的發明和發展,提供了穩定性好的大功率源。(6) 使用多普勒頻移來檢測淹沒于雜波中的移動目標。(7)適于空中交通管制的雷達的開發。(8) 脈沖壓縮。(9) 單脈沖跟蹤雷達有高的跟蹤精度,以及比以前的跟蹤雷達對電子對抗措施有更好的抵御能力。(10) 合成孔徑雷達,對地面場景和地面上的物體成像。(11) 機載動目標顯示 (AMTI) ,用于在有雜波情況下遠程機載空中監視。(12) 穩定的元件、子系統和超低副瓣天線,使可大量抑制無用雜波的高 P 盯脈沖多普勒雷達 (AWACS) 成為可能。(13) 高頻超視距雷達,把飛機和艦船的探測距離擴大了一個數量級。(14) 數字處理,從 20 世紀 70 年代早期對雷達性能的改善有重大影響。(15) 監視雷達的自動檢測和跟蹤。黃河科技學院畢業設計(文獻翻譯) 第 12 頁—————————————————————————————(16) 電掃描相控陣?yán)走_(dá)的批量生產。(17) 逆合成孔徑雷達 CISAR) ,提供目標成像,如對艦船等非合作目標識別需要的圖像。(18) 多普勒氣象雷達。(19) 太空雷達,適于對如金星等行星進行觀測。(20) 計算機對復雜目標雷達截面積的精確計算。(21)多功能機載軍用雷達,體積和質量相對小,適于安裝在戰斗機前端,具有執行大量不同的雪一空和空地任務的功能。以上是對雷達過去一些主要發展的一點觀點。其他人或許有不同的看法。并非每種重大的雷達成就都包括在內。如果包括本書其他章節的內容,這個列表可能會更長并包含更多的例子。但是這個列表己足以顯示出對雷達性能改進很重要的進展類型。
收藏