【溫馨提示】 dwg后綴的文件為CAD圖,可編輯,無水印,高清圖,,壓縮包內文檔可直接點開預覽,需要原稿請自助充值下載,請見壓縮包內的文件及預覽,所見才能所得,請細心查看有疑問可以咨詢QQ:414951605或1304139763
黑龍江工程學院本科生畢業設計
摘 要
隨著我國交通運輸業的迅猛發展,汽車的增多,汽車的使用越來越普遍。汽車在高速行駛時,其穩定性受前輪定位參數影響較大,其中,以車輪外傾和前束兩參數的影響為最大。當車輪前束值和車輪外傾角配合不當時,會引起車輪承受側向力而產生側向滑移現象,這將破壞車輪的附著條件,喪失定向行駛的能力,引發交通事故并導致輪胎的異常磨損。
在汽車行駛時前輪側滑量直接反映了前輪定位參數調整的準確與否,汽車側滑檢測臺用來檢查車輪側滑量的大小與方向,從而確認車輪前束與車輪外傾角的配合是否恰當。汽車前輪通過側滑臺滑板時,由于滑板的側向移動僅受滑板與支撐滾輪間的摩擦力和滑板的回位彈簧拉力的約束,同時輪胎與滑板間有足夠的側向位移。這樣,在前束和外傾的綜合作用下,若前輪的自由滾動方向偏離實際行駛方向,只要所產生的側向力大于滑板與滾輪間摩擦力和彈簧彈性恢復力之和,前輪向前滾動的同時便會帶動滑板側滑。這設計包括側滑板,鋼板,直線位移傳感器,鋼槽,導軌,底座等等。
關鍵詞:汽車;側滑;檢測;位移傳感器;;導軌
ABSTRACT
With rapidly developing of traffic and transport as well as rising of vehicles in our country, The number of double-front-axle steering automobile is also increasing. When the car is driving at high speed, its stability is deeply effected by front wheel alignment parameters. Among them, the toe-in value and camber value have the largest effection. When the toe-in value cann’t match the camber angle, it will induce the wheel supporting side direction force, consequently come into being slid phenomenon. It’ll induce traffic accidents and cause tires’ abnormal wearing.
During the automobile’s driving period, front-wheel slid value impact directly to the correction or not of front wheel alignment parameters adjustment. Car slid tester is used to check the amount and direction of wheels’ slid value. To ensure the correct matching between wheel toe-in and wheel camber angle. Auto front through the sideslip tester, because the board by moving subject only to the skateboard wheel and support the friction between the return of spring tension and skateboard, while the constraints between tires and skateboarding has enough lateral displacement. So, before the comprehensive function outward exert bundles and, if the freedom front wheel rolling direction deviating from the practice driving direction, as long as the lateral force generated more than skateboard and roller of friction and spring between elastic restoring force, the sum of the front wheel rolling forward while will drive skateboarding lateral spreads. This designation introduces Side skateboard steel Linear displacement sensor Steel racks guide base and so on.
Key words: Automobile; Slid;Moritering;Ddisplacement sensor;Gui
II
目 錄
摘要 I
ABSTRACT II
第1章 緒 論 1
1.1 課題的提出 1
1.2 國內外相關技術的現狀及發展方向 1
1.3 課題的主要研究內容及技術途徑 2
第2章 側滑檢測臺總體方案的論證 5
2.1 側滑的基礎知識 5
2.1.1 側滑的產生原因 5
2.1.2 正前束引起正側滑,正外傾引起負側滑 5
2.1.3 影響側滑量的因素 6
2.1.4 汽車前輪側滑量對汽車使用性能的影響 6
2.2 側滑試驗臺的結構與工作原理 7
2.2.1 側滑試驗臺設計方案的確定 7
2.2.2 單板式側滑臺的工作原理 8
2.3本章小結 10
第3章 側滑檢測臺設計說明 12
3.1 側滑檢測臺機械系統設計說明 12
3.1.1總體尺寸的確定 12
3.1.2材料的選擇 13
3.1.3側滑板機械結構設計 13
3.1.4側滑檢測臺及各零件尺寸 15
3.2 側滑檢測臺控制系統設計說明 16
3.2.1 硬件系統結構及工作原理 16
3.2.2傳感器的選擇及其信號處理電路設計 16
3.3 本章小結 18
第4章 側滑檢測臺的技術要求 19
4.1 側滑檢測臺的使用方法 19
4.1.1 檢測前的準備 19
4.1.2檢測步驟 19
4.1.3 檢測時的注意事項 19
4.2 側滑臺的維護 20
4.3側滑檢測臺的檢定和調整 20
4.3.1側滑檢測臺的檢定 20
4.3.2 側滑檢測臺的調整 20
4.4本章小結 23
結 論 24
參考文獻 25
致 謝 26
附 錄 27
附 錄
28