以上為資料預覽概圖，下載文件后為壓縮包資料文件。【清晰，無水印，可編輯】dwg后綴為cad圖，doc后綴為word格式，需要請自助下載即可，有疑問可以咨詢QQ 197216396 或 11970985

編號： 　畢業設計(論文)開題報告 題 目： 應急燈外殼注塑模具設計 院 （系）： 專 業： 學生姓名： 學 號： 指導教師單位： 姓 名： 職 稱： 題目類型：¨理論研究 ¨實驗研究 t工程設計 ¨工程技術研究 ¨軟件開發 1．畢業設計的主要內容、重點和難點等 畢業設計的主要內容： 畢業設計課題為時尚藝術塑料板凳注塑模具設計。近幾年，我國塑料模具工業有了很大的發展，塑料制品在我們的日常生活中扮演著越來越重要的角色，其種類也越來越多，制造加工也越來越精致美觀。在未來的模具市場中，塑料模具發展的速度將高于其它模具，在模具行業中的比例將逐步提高。并且隨著注塑模具技術的發展，在工程機械和工業機械、電子、汽車、家電、玩具等產品中，60%以上的零部件，可以依靠模具成型。? 隨著國內經濟發展，居民生活水平的提高，塑料板凳已經成為日常生活中常備的用品。塑料板凳也出現了多種樣式，其中更多的板凳以其精美的外觀，低廉的價格，以及耐用的特點而受到企業和廣大消費者的歡迎。塑料板凳雖然看似簡單，但是其注塑模具的設計制造所涉及的知識面和知識點比較多，能比較全面的反應一些注塑模具設計的特點。本課題應用性強，知識面覆蓋較廣，并且來自生活，所以容易激發我學習研究的興趣，所以選擇了這個課題,其主要內容如下： 1、參觀調研，查閱資料。到模具制造相關企業調研，了解模具設計、生產、制造及加工情況。結合本次畢設課題，查閱模具相關資料； 2、 撰寫開題報告； 3、通過對產品的性能分析，完成相關的模具結構與零件設計； 4、設計的模具結構要求完整、合理； 5、合理選擇尺寸、公差、表面粗糙度和制件材料，繪制的產品圖樣完整； 6、認真分析制件圖，確定模具型腔、模具結構、分型面和進料口形式，計算含收 縮率的相關尺寸和模具的強度和剛度； 7、 翻譯專業外語文獻。 8、 撰寫畢業設計（論文）說明書； 9、 繪制模具總裝圖、零件圖； 畢業設計的重點難點： 1、脫模推出機構和側抽芯機構的設計； 2、塑件的合理性設計及結構工藝性分析； 3、材料選擇，收縮率計算。模具強度及剛度分析； 4、塑件壁厚成型工藝考慮及保證塑件的外觀要求； 5、模具型腔數的確定，模具結構、分型面和進料口形式的選擇； 6、保證塑件成型時無變形，注出的制件表面光滑，無氣泡和其它缺陷，無飛邊或少飛邊。 7、繪制模具總裝圖、零件圖及尺寸標注。 2．準備情況（查閱過的文獻資料及調研情況、現有設備、實驗條件等） 1、 模具技術的現狀 模具是汽車、電子、電器、航空、儀表、輕工、塑料、日用品等工業部門極其重要的工藝裝備。沒有模具、就沒有高質量的產品。模具不是一般的工藝裝備，而是技術密集型的產品，工業發達國家把模具作為機械制造方面的高科技產品來對待。他們認為：“模具是發展工業的一把鑰匙；模具是一個企業的心臟；模具是富裕社會的一種動力”。? 近年來,我國塑料模具業發展相當快，目前，塑料模具在整個模具行業中約占30%左右，而在整個塑料模具市場以注塑模具需求量最大。隨著模具制造行業的發展，許多企業開始追求提高產品質量及生產效率,縮短設計周期及制造周期,降低生產成本，最大限度地提高模具制造業的應變能力等目標。新興的模具CAD技術很大程度上實現了企業的愿望。近年來，CAD技術的應用越來越普遍和深入,?大大縮短了模具設計周期,?提高了制模質量和復雜模具的制造能力。? 目前，美國、日本、德國等工業發達國家模具工業的產值均已超過機床工業總產值。美國模具年產值已超過1O0億美元；日本從1957年到1984年二十七年間，?模具工業增長100倍；1987年臺灣地區模具出口達一億二千萬美元。香港的模具年產值為30億港幣，我國的模具年產值為人民幣3O億元。? 從整體來看，中國塑料模具無論是在數量上，還是在質量、技術和能力等方面都有了很多進步，但與國民經濟發展的需求、世界先進水平相比，差距仍然很大。主要缺陷明顯的表現在精度不高，技術含量低、復雜程度低等缺點。嚴重的阻礙著國內模具業的發展。一些大型、精密、 復雜、長壽命的中高檔塑料模具每年仍需大量進口。在總量供不應求的同時，一些低檔塑料模具卻供過于求，市場競爭激烈，還有一些技術含量不太高的中檔塑料模具也有供過于求的趨勢。因此中國塑料模具行業和國外先進水平相比，主要存在一下問題：發展不平衡，產品總體水平較低；工藝裝備落后，組織協調能力差；大多數企業開發能力弱，創新能力明顯不足；供需矛盾短期難以緩解；體制和人才問題的解決尚需時日。這些都嚴重的阻礙著國內電子業的發展。設計出好的產品卻無法做出是我模具業的最大不足。因此，注重科技含量，借助了國外的先進理論技術則尤為重要。? 大型化、高精密度、節能復合型模具將是未來注塑模具的發展方向。隨著國際化，市場競爭越來越激烈，短周期、高質量、長壽命的高檔塑料模具也會加大研制與開發。同時，注塑模具將與并行工程、精益生產、敏捷制造等多種生產模式密切結合，最終使塑料模具行業發生重大變革。 2、注塑模簡介 注塑成型又稱注塑模具，是熱塑性塑料制件的一種主要成型方法，并且能夠成功地將某些熱固性塑料注塑成型。注塑成型可成型各種形狀的塑料制品，其優點包括成型周期短，能一次成型外形復雜、尺寸精密、帶有嵌件的制品，且生產效率高易于實現自動化，因而廣泛應用在塑料制品生產當中。 3、注塑成型原理及特點 塑料的注塑成型過程，就是借助螺桿或柱塞的推力，將已塑化的塑料熔體以一定的壓力和速度注入模具型腔內，經過冷卻固化定型后開模而獲得制品。因此，可以說注塑成型在塑料裝配生產中具有重要地位。 4、注塑成型原理 注塑成型所用的模具即為注塑模（也稱為注射模），注塑成型的原理（以螺桿式注射機為例）。首先將顆粒或粉狀的塑料加入料斗，然后輸送到側裝有電加熱的料筒中塑化。螺桿在料筒前端原地轉動，使被加熱預塑的塑料在螺桿的轉動作用下通過螺旋槽輸送至料筒前端的噴嘴附近。螺桿的轉動使塑料進一步化，料溫在剪切摩擦熱的作用下進一步提高并得以均勻化。當料筒前端堆積的體對螺桿產生一定的壓力時（稱為螺桿的背壓），螺桿將轉動后退，直至整好的行程開關接觸，從而使螺母與螺桿鎖緊。具有模具一次注射量的塑料預塑和儲過程結束。 這時，馬達帶動氣缸前進，與液壓缸活塞相連接的螺桿以一定的速度和壓力將熔料通過料筒前端的噴嘴注入溫度較低的閉合模具型腔中。熔體通過噴嘴注入閉合模具腔后，必須經過一定時間的保壓，熔融塑料才能冷卻固化，保持模具型腔所賦予形狀和尺寸。當合模機構打開時，在推出機構的作用下，即可頂出注塑成型的塑料制品。 5、應急燈外殼注塑模具設計的流程： (1)思考與創新：繪制草圖，確定應急燈外殼的外觀形式； (2)實踐操作：通過Pro-e軟件畫出應急燈外殼的三維模型； (3)用Pro-e做出內部的結構，實現外觀要求； (4)將Pro-e做的圖導入AutoCAD中； (5)修改結構圖。 6、注射模具的設計過程 (1)對塑料零件的材料、形狀和功能進行分析 (2)確定型腔的數目 確定型腔的數目條件有：最大注射量、鎖模力、產品的精度要求和經濟性等。 (3)選擇分型面 分型面的選擇應以模具結構簡單、分型容易，且不破壞已成型的塑件為原則。 (4)型腔的布置方案 型腔的布置應采用平衡式排列，以保證各型腔平衡進料。型腔的布置還要注意與冷卻管道、推桿布置的協調問題。 (5)確定澆注系統 澆注系統包括主流道、分流道、澆口和冷料穴。澆注系統的設計應根據模具的類型、型腔的數目及布置方式、塑件的原料及尺寸等確定。 (6)確定脫模方式 脫模方式的設計應根據塑件留在模具的部分而同。由于注射機的推出頂桿在動模部分，所以，脫模推出機構一般都設計在模具的動模部分。因此，應設計成使塑件能留在動模部分。設計中，除了將較長的型芯安排在動模部分以外，還常設計拉料桿，強制塑件留在動模部分。但也有些塑件的結構要求塑件在分型時，留在定模部分，在定模一側設計出推出裝置。推出機構的設計也應根據塑件的不同結構設計出不同的形式，有推桿、推管和推板等結構。 (7)確定調溫系統結構 模具的調溫系統主要由塑料種類決定。模具的大小、塑件的物理性能、外觀和尺寸精度都對模具的調溫系統有影響。 (8)確定凹模和型心的固定方式 當凹?；蛐托牟捎描倝K結構時，應合理地劃分鐵塊并同時考慮鑲塊的強度、可加工性及安裝固定。 (9)確定排氣尺寸 一般注射模的排氣可以利用模具分型面和推桿與模具的間隙；而對于大型和高速成型的注射模，必須設計相應的排氣裝置。 (10)確定注射模的主要尺寸 根據相應的公式，計算成型零件的工作尺寸，以及決定模具型腔的側壁厚度、動模板的厚度、拼塊式型腔的型腔板的厚度及注射模的閉合高度。 (11)選用標準模架 根據設計、計算的注射模的主要尺寸，來選用注視模的標準模架，并盡量選擇標準模具零件。 (12)繪制模具的結構草圖 在以上工作的基礎上，繪制注射模的完整的結構草圖，繪制模具結構圖是模具設計十分重要的工作，其步驟為先畫俯視圖（順序?yàn)椋寒嬆＜堋⑿颓?、冷卻管道、支撐柱、推出機構），再畫出主視圖。 (13)校核模具與注射機有關尺寸 對所使用的注射機的參數進行校核：包括最大注射量、注射壓力、鎖模力及模具的安裝部分的尺寸、開模行程和推出機構的校核。 (14)注射模結構設計的審查 對根據上述有關注視模結構設計的各項要求設計出來的注射模，應進行注射模結構設計的初步審查，同時，也有必要對提出的要求加以確認和修改。 (15)繪制模具的裝配圖 裝配圖是模具裝配的主要依據，因此應清楚地表明注視模的各個零件的裝配關系、必要的尺寸（如外形尺寸、定位圈直徑、安裝尺寸、活動零件的極限尺寸等）、序號、明細表、標題欄及技術要求。 (16)繪制模具的零件圖 由模具裝配圖拆繪零件圖的順序?yàn)椋合葍?nèi)后外，先復雜后簡單，先成型零件后結構零件。 (17)復核設計圖樣 注射模具設計的最后是審核所設計的注射模，應多關注零件的加工、性能。 已查閱的文獻資料 [1] 大連理工大學工程畫教研室編.機械制圖[M],高等教育出版社，2003 [2] 葉久新 王群主編.塑料成型工藝及模具設計[M]，機械工業出版社,2007. [3] 屈華昌主編.塑料成型工藝與模具設計.北京[M]：機械工業出版社，1996. [4] 翁其金．塑料模塑成型技術[M]．北京：機械工業出版社，2000.2 [5] 模具實用技術叢書編委會．模具實用技術注塑模具設計制造與應用實例[M]．北京：機械工業出版社2002.2 [6] 陳世煜 陳可娟．塑料注塑成型模具設計[M]．北京：國防工業出版社，2007.9 [7] 唐志玉．大型注塑模具設計原理與應用[M]．北京：化學工業出版社，2002.1 [8] 王樹勛 朱亞林．注塑模具設計[M]．廣州：華南理工大學出版社，2005.5 [9] 模具設計編委會．塑料模具技術手冊[M]．北京：機械工業出版社，2002.5 [10] 李學鋒．塑料模設計及制造[M]．北京：機械工業出版社，2002.6 [11] 王敏杰 宋滿倉．模具制造技術[M]．北京：電子工業出版社, 2004．7 [12] 田福祥．五板式推板推件高壓聚乙烯堵頭注塑模[J]．塑料科技．2007（2） [13] 朱光.塑料注塑模中小型模架及其技術條件[M]。北京：清華大學出版社，2003,1 [14] cunha,L,et.al.,performance of chromium nitride and titanium nitride coatings during platics injection moulding. Surface and coating Technology,2002.153(2-3):p.160-165. 現有設備及實驗條件：計算機一臺，使用軟件為Pro/Engineer5.0及Auto CAD2008、Moldflow insight，以上實驗條件可滿足本次畢業設計的要求。 3、實施方案、進度實施計劃及預期提交的畢業設計資料 1.2013年12月17日至2013年12月30日，理解消化畢設任務書要求并收集、分析、消化資料文獻，根據畢設內容完成并交開題報告； 2.2013年1月6日至2014年1月13日，開展調研，了解塑件結構，對原材料進行分析，考慮塑件的成型工藝性、模具的總體結構的形式，并完成部分英文摘要翻譯。 3.2014年3月4日至2013年3月31日，查閱資料，熟悉注射模的結構及有關計算，擬定模具的方案設計、總體設計及主要零件設計，擬定成型工藝過程，查閱有關手冊確定適宜的工藝參數，注射機的選擇及確定注射設備及型號規格； 4.2014年4月1日至2014年4月21日，完成設計計算任務，總體結構的設計和完成總裝配圖及零件圖的設計； 5.2014年4月22日至2014年5月1日，完成設計，圖紙繪制任務，工藝規程說明書的編寫； 6.2014年5月1日至2014年5月4日，完善設計并完成論文的撰寫； 7.2014年5月4日至2014年5月8日，修改并打印畢業論文及整理相關資料，交指導老師評閱，準備論文答辯。 指導教師意見 指導教師（簽字）： 2013年12月　　日 開題小組意見 開題小組組長（簽字）： 2014年1 月　　日 院（系、部）意見 主管院長（系、部主任）簽字： 2014年1月　　日 - 8 - 編號： 　畢業設計（論文）外文翻譯 （譯文） 學 院： 國防生學院 專 業：機械設計制造及其自動化 學生姓名： 陽則華 學 號： 1000110113 指導教師單位： 機電工程學院 姓 名： 郭中玲 職 稱： 高級工程師 2014年1月10日 第 19 頁 共 20頁 桂林電子科技大學畢業設計（論文）報告用紙 注塑模具的設計與熱分析 摘 要:本文介紹了用于生產熱變形測試樣品的注塑模具的設計，這種模具能為自身實現熱分析，從而得到模具的熱殘余應力的影響。文章對技術，理論，方法以及在注塑模型設計中需要的考慮的因素也進行了介紹。模具設計是通過商用計算機輔助設計軟件Unigraphics系統的13.0版本實現的。這種用于分析因樣品不均勻冷卻產生的熱殘余應力的模具，已經通過使用13.5版的被稱作LUSAS分析員的商業有限元分析軟件得到了開發，而且存在問題也已經解決。該軟件通過繪制相應的時間反應曲線為模具提供了溫度分布等高線圖以及注塑周期中的溫度的變化。結果表明，與其他區域相比，收縮可能更容易發生在冷卻渠道附近的區域。熱變形就是這種在模具的不同區域的不均衡降溫效果引起的。 關鍵詞：注塑模具；設計；熱分析 1. 引言 塑料業是世界上發展最快的工業之一，被列入產值達數十億美元的產業。幾乎每一個在日常生活中使用的產品都涉及塑料的使用，這些產品大部分可通過注塑成型方法生產［1］。注塑成型工藝因其制造過程是以較低的成本生產各種形態和復雜幾何形狀的產品而眾所周知［2］。 注塑成型工藝是一個循環工藝，整個過程分為四個重要的階段，即：充模，保壓，冷卻和噴射。在注塑成型過程是從漏斗中把樹脂和適當?shù)奶砑觿┳⑷氲阶⑺艹尚蜋C(jī)的加熱/注射系統開始的［3］。這就是“充模階段”，在這個過程中，模腔填充了達到注射溫度的熱聚合物熔體。在模腔填充后的 “保壓”階段，更多的是聚合物熔體在更高的壓力下被裝進腔體，以補償因聚合物固化引起的預計萎縮。接下來便是冷卻階段，在此過程中模具會冷卻，直到有足夠的剛性部分被彈出。最后一個階段是“彈射階段”，這個階段模具被打開，成型部分被彈出，過后，模具會再次被關閉開始下一個循環［4］。 因?yàn)橹饕强拷?jīng)驗，包括了實際工具的反復修改，所以設計和制造所需性能的注塑成型聚合物部件的過程很昂貴的。在模具設計任務中，由于包含了噴射和氣壓因素，通常來說，在核心區為模具設計特別附加的幾何結構是相當復雜［5］。 為了設計出模具，許多重要的設計因素必須加以考慮。這些因素是模具的大小，模腔的數量、布局，熱流道系統，門控系統，收縮和彈射系統［6］。 在模具的熱分析中，其主要目的是分析熱殘余應力或模壓對產品尺寸方面的影響。熱誘導應力主要發生在注塑零件的冷卻階段，主要是由于其較低的熱傳導率和熔融樹脂和模具之間的溫度差異。在場冷卻過程中的產品腔的溫度是不平衡的［7］。 冷卻過程中，離冷卻通道越近的地方能更大程度的冷卻下來。這種溫度的不同引起了材料的異收縮，從而帶來熱應力。明顯的熱應力可能會引起變形問題。因此，在注射成型過程的冷卻階段對熱殘余應力場進行模擬是非常重要的［8］。通過了解熱殘余應力的分布特點，我們就可以預測熱殘余應力引起的變形。 在這篇論文中，為生產翹曲測試樣本設計的提出了這樣一種注塑模具設計：它能對模具實現熱殘余應力對其的影響實現熱分析。 2. 方法 2.1 翹曲測試樣本的設計 這一部分介紹了用于注塑模具設計的翹曲測試樣本的設計。對于外殼很薄的產品來說，很明顯翹曲是存在其中的主要問題。因此，產品開發的主要目的就是設計一個塑件能為外殼很薄的注塑模具的翹曲問題確定影響因素。翹曲測試樣本是由薄塑料殼而開發的。樣本的總體尺寸是長120毫米，寬50毫米，厚1毫米。生產翹曲測試樣本所用材料是丙烯腈丁二烯苯乙烯（ABS）注塑的溫度、時間和壓力分別是210 ?C, 3 s 和 60MPa,圖1表示翹曲測試樣本。 圖1 翹曲測試樣本 2.2 翹曲測試樣本設計注塑模具 本節介紹了用于生產翹曲測試樣本的模具的設計部分和設計中其他需要考慮的因素。用于生產翹曲測試樣本注塑模具的材料是美國國家鋼鐵學會的1050碳鋼。在模具設計中考慮到的四個設計概念包括： I. 三板模具（概念1）有兩個分模線單腔，由于成本高所以不適用。 ii. 二板模具（概念2）有無澆注系統的一個分模線單腔。由于每注的低生產率而不適用。 iii. 二板模具（概念3）有一分模線與門控噴射系統的雙腔。由于產品太薄，頂針可能損害它，因此也不適用。 iv. 二板模具（概念4）有一分模線與有門控系統的雙腔，只用直澆口拉出器作為噴射器，來避免在噴射過程中對產品的破壞。在翹曲樣本的模具設計中第四個設計概念已經得到應用。 各種設計根據都已經在設計中得到應用。 首先，模具的設計是基于所使用注塑機器的壓盤尺寸(BOY 22D)。這個機器是有一定限制的，這就是兩個拉桿之間的距離定出的壓板機的最大面積在機器拉桿之間的距離為254毫米。因此，模具板最大寬度應不能超過這個距離。此外，為了達到調定和處理模具的目的，在兩個拉桿和模具之間保留了4毫米的空間。最終這使模具的最高寬度為250毫米。標準模具基地有250×250毫米的使用面積。模具基底是用美得麗鉗安裝在模具基座或模具壓板右上角和左下角的。其他相關模具板的尺寸見表1。 設計了夾緊壓力的模具具有高于內部空腔力（反應力）的夾緊力來避免發生突然的活動。 表1 磨具板尺寸 部件 尺寸：寬度×高度×厚度 頂部壓緊板 250×250×25 腔板 200×250×40 核心板 200×250×40 側板，支撐板 37×250×70 排出維持板 120×250×15 推出器 120×250×20 底部固定板 250×250×25 基于標準模具系列給出的尺寸，寬度和核心板的高度分別是200和250毫米 這些尺寸使核心板兩腔的設計是水平放置的，因?yàn)榍话鍨榭諘r(shí)有足夠的空間，為了填充熔融塑料，只是用澆口襯瓦來固定因此，在產品表面只設計了一個標準分型線。在模具打開的過程中，產品和滑行裝置放置在通過分型面的一個平面上，標準門或側門就是轉為這個模具設計的。門就處在滑道和產品之間。在門底部的土地，設計了20?傾斜，而且厚度只有0.5毫米以便于清鏟。 這個門還設計了四毫米寬0.5毫米厚的熔融塑料入口。在模具設計中，選擇了滑道的拋物線交叉部分的類型，因?yàn)樗幸粋€(gè)好處，那就是一模只需一半的簡單加工，即這一例子中的核心板。 盡管如此，與圓截面類型相比這種滑道有諸如更多的熱流失和廢料。這可能會引起熔融塑料更快的凝固。這個問題通過使用更短，直徑更大的滑道得以減少，它的直徑是6毫米。非常重要的一點是滑道的設計要同時在相同的壓力和溫度下把材料或熔融塑料分送到腔體中。由于這一點，腔體的布局設計成了對稱形式。設計中另一個需要考慮的方面就是通氣孔的設計。 為了防止發生滑動，核心和板腔之間的配合面板加工非常精細。但是，這可能導致在模具關閉時空氣被封在里面，而使產品出現噴丸不足或部分不完整。為了確保鎖住的空氣能被排出來而避免部分不完整的發生，我們?cè)O(shè)計了足夠多的通氣孔。冷卻系統是沿著模具的長度鉆出來的，在與模具水平的位置使其更好的冷卻這些冷卻渠道在兩鉆腔和和核心板上都有。它們使模具在湍流的情況下能夠充分的被冷卻。圖2 給出了通氣孔和核心板上的冷卻渠道在腔里的布局。 圖2 氣孔在腔中的布局及冷卻通道 在這個模具設計中，彈射系統包括彈射版，直澆口拉出器以及噴射器。位于核心板中心位置的直澆口拉出器的作用不只是作為模具打開時固定產品位置的拉出器，而且在噴射階段作為噴射器把產品從模具中推出來。在產品腔中沒有放置和使用附加的噴射器，因?yàn)楫a(chǎn)品生產的非常薄，即1毫米。 產品腔中額外的注射器可能會在噴射階段給產品增加洞眼和損害。最后，要對尺寸容差進行足夠的考慮來補償材料的收縮。圖3顯示了利用unigraphic系統建立的三維實體造型以及線框模型 圖3 模具的三維實體建模和線框模型 圖4 用于避免欠注的額外的通風孔 3. 結果和討論 3.1 生產和調整產品的結果 從設計和制作的模具來看，生產的翹曲測試樣本在實驗跑中有一些缺陷。這些缺陷是短射，溢料和翹曲。短射隨后被彎道腔排氣孔的邊緣消除來使被困住的空氣能出來。與此同時，溢料也通過減少保壓機器的壓力得到降低。變形可以通過控制諸如注射時間，注射溫度和融融溫度等各種參數來得到控制。經過這些修改，模具生產了高品質低成本的翹曲測試樣本同時需要盡快完成小門控。圖4顯示了模具的修改，正在加工消除短射的額外排氣孔。 3.2 模具和產品的細節分析 模具和產品開發出來以后, 就進行對模具和產品的分析t. 在注塑成型額過程中, 210度的熔融ABS通過腔板上的澆口套注入模具直接即進入到產品腔。冷卻發生后，產品就成型了One 產品的周期大約需要35秒，而其中冷卻的時間就有20秒。生產翹曲測試樣本的材料是ABS，其注塑溫度，時間，和壓力分別是210度，3秒和60MPa。 模具選的材料是1050碳鋼，這些材料的性能在有限元素分析開發的模具中決定溫度分布的方面是非常重要的。表2顯示了ABS和AISI1050碳鋼的性能。對模具進行分析的關鍵部分在于腔體和核心板，因?yàn)檫@是產品成型的地方。 所以熱分析來知道溫度分布和不同時間的不同溫度是通過采用商業有限元素分析軟件即所謂的LUSAS分析員的13.5版本來實現的。為了研究在不同地區熱殘余應力對模具的影響，進行了二維的熱分析，由于是對稱的，熱分析只要通過垂直截面的上半部分或者在注射階段被夾住的兩腔的側面和核心板塊。圖5顯示了用不規則網格分析的熱分析模型。 圖5 熱分析模型 建模還涉及到性能分配和模型的程序或周期的時間。這使得有限求解分析模具模型建立，并且繪制了時間反應圖來顯示在特定階段的不同地區的溫度變化。對于產品的分析，是通過利用LUSAS分析員的13.5版本實現了一個二維拉伸應力分析?；旧显诒痪o緊地加載在一端，而另一端是被鎖住的。負荷會一直增長知道模型達到可塑性。圖6顯示了分析的加載模式。 表格2 模具和產品的材料性能 圖6 分析的加載模式 圖7 不同時間間隔的二維熱分布等高線圖 3.3 對模具和產品分析的結果和討論 對于模具分析來說，可以觀察到不同的時間間隔中的熱量分布。圖7顯示了一個完整注塑模型周期中不同時間間隔的熱分布二維分布等高線圖。 對于模具的分析來說，在不同熱量或熱能分布等高線繪制圖上 ，熱量分布在一個完整的注塑周期中。為了實現對于模具的二維分析，繪制了時間反應曲線圖來分析熱殘余壓力對產品的影響。圖8顯示了為了繪制時間反應曲線選出的結點。 圖8 時間反應曲線圖選出的結點 圖9.17顯示了圖8 所示不同節點上的溫度分布曲線。 從繪制出的溫度分布曲線圖來看，圖9.17中，為繪制曲線圖選擇的每一個結點在溫度上會經歷上升。即，從其周圍的溫度到比其周圍溫度高的特定溫度，然后在特定的一個時間里，在這個溫度上保持不變。這個溫度增長是由于熔融塑料被注入產品腔引起的。From the temp一段特定的時間.過后，溫度會進一步升高直到最高溫度，然后保持在那個溫度上。溫度增長歸因于引起高壓的保壓階段。這個階段上引起溫度上升。這個溫度會一直維持到冷卻階段開始，這個階段上把模具的溫度降并維持到一個較低的值。繪制的曲線由于沒有熔融塑料的注入率以及冷卻劑的制冷率，他是彎曲的。繪制的曲線只是顯示了在周期中能夠達到的最大值。熱殘余應力分析的最關鍵步驟是冷卻階段。這是因?yàn)椋鋮s階段引起了材料從高于玻璃轉化溫度到低于它的轉化。材料經歷了可能導致翹曲的引起熱應力的不同的收縮。從圖9.17所示的冷卻以后的溫度中，由于溫度進一步降低冷卻管附近的溫度會很明顯的受到更大的冷卻效果，而遠離冷卻管的地方則有較小的冷卻效果冷卻率越大，冷卻效果越多意味著在這個地方發生跟大的收縮。盡管如此，最遠的地方，第284結點，盡管遠離冷卻管，由于向環境中損失的熱量，經歷更大的冷卻力。結果是，產品腔中心位置的冷卻管引起中間高于其他地方的部分的溫度不相同.。由于更大程度的收縮，中間部分產生了壓縮，同時由于收縮不均等引起了翹曲。盡管如此，冷卻后，不同結點的溫度差異很小，翹曲影響也不明顯。 對設計師而言，設計一個有較少熱殘余應力及及有效的冷卻系統的模具是非常重要的。對產品的分析，從開始進行分析注塑產品的階段，不同的負載因子在產品上的壓力分布在這兩個尺寸分析中得到觀察。圖18—21顯示了不同負荷應力增量的等高線圖。一個臨界點，即127節點上，產品的最大拉應力被選定出來進行分析。在圖22和23 中繪制了這一點上的壓力應變曲線和負載應力曲線從圖23繪制的這一點上的負載應力曲線，很清楚的看到產品經受很大的負荷，直到23的負載力，即1150牛。這意味著產品能夠承受最大在1150牛的拉伸力。高于這個值的負荷會引起產品的失靈?；趫D23，失靈很可能會發生在產品的固定端附近的區域，這里最大應力是3.27×107 Pa 。由于該產品的生產是以為了翹曲測試，也沒有分析與拉伸荷載的關系，所以其應力分析揭示的是很有限的信息。未來，盡管如此，建議產品服務條件應該確定，以便能夠進行各種其他的負載下的進一步分析。 圖9 284結點溫度分布圖 圖10 213結點的溫度分布圖 圖11 302結點的溫度分布圖 圖12 290結點的溫度分布圖 圖13 278結點的溫度分布圖 圖14 1830結點的溫度分布圖 圖15 1904結點的溫度分布圖 圖16 1853結點的溫度分布圖 圖17 1866結點的溫度分布圖 圖18 在荷載增量為1時的等效應力圖 圖19 在荷載增量為14時的等效應力圖 圖20 在荷載增量為16時的等效應力圖 圖21 在荷載增量為23時的等效應力圖 圖22 ABS的應力與應變曲線 圖23 ABS樹脂的應力與荷載增量曲線 4. 結論 設計的模具可以生產用于確定影響翹曲參數的高質量的翹曲測試樣本。該測試樣本生產成本低，只涉及很少德控門的修整。注塑模具的熱分析提供了熱殘余應力對標本的變形后形狀的影響的解釋另外對產品拉伸應力的分析成功的預測翹曲測試樣本在出現失靈之前的拉伸載荷。 鳴謝：作者向發起本文出版的馬來西亞博特拉大學工程學院致謝。 參考文獻 [1] R.J. Crawford, Rubber and Plastic Engineering Design and Applica- tion, Applied Publisher Ltd., 1987, p. 110. [2] B.H. Min, A study on quality monitoring of injection-molded parts, J. Mater. Process. Technol. 136 (2002) 1. [3] K.F. Pun, I.K. Hui, W.G. Lewis, H.C.W. Lau, A multiple-criteria envi- ronmental impact assessment for the plastic injection molding process: a methodology, J. Cleaner Prod. 11 (2002) 41. [4] A.T. Bozdana, O¨ . Eyerc′?og? lu, Development of an Expert System for the Determination of Injection Moulding Parameters of Thermoplastic Materials: EX-PIMM, J. Mater. Process. Technol. 128 (2002) 113. [5] M.R. Cutkosky, J.M. Tenenbaum, CAD/CAM Integration Through Concurrent Process and Product Design, Longman. Eng. Ltd., 1987, p. 83. [6] G. Menges, P. Mohren, How to Make Injection Molds, second ed., Hanser Publishers, New York, 1993, p 129. [7] K.H. Huebner, E.A. Thornton, T.G. Byrom, The Finite Element Method for Engineers, fourth ed., Wisley, 2001, p. 1. [8] X. Chen, Y.C. Lam, D.Q. Li, Analysis of thermal residual stress in plastic injection molding, J. Mater. Process. Technol. 101 (1999) Journal of Materials Processing Technology 171 2006 259 267 Design and thermal analysis of plastic injection mould S H Tang Y M Kong S M Sapuan R Samin S Sulaiman Department of Mechanical and Manufacturing Engineering Universiti Putra Malaysia 43400 Serdang Selangor Malaysia Received 3 September 2004 accepted 21 June 2005 Abstract This paper presents the design of a plastic injection mould for producing warpage testing specimen and performing thermal analysis for the mould to access on the effect of thermal residual stress in the mould The technique theory methods as well as consideration needed in designing of plastic injection mould are presented Design of mould was carried out using commercial computer aided design software Unigraphics Version 13 0 The model for thermal residual stress analysis due to uneven cooling of the specimen was developed and solved using a commercial nite element analysis software called LUSAS Analyst Version 13 5 The software provides contour plot of temperature distribution for the model and also temperature variation through the plastic injection molding cycle by plotting time response curves The results show that shrinkage is likely to occur in the region near the cooling channels as compared to other regions This uneven cooling effect at different regions of mould contributed to warpage 2005 Elsevier B V All rights reserved Keywords Plastic Injection mould Design Thermal analysis 1 Introduction Plastic industry is one of the world s fastest growing industries ranked as one of the few billion dollar industries Almost every product that is used in daily life involves the usage of plastic and most of these products can be produced by plastic injection molding method 1 Plastic injection molding process is well known as the manufacturing process to create products with various shapes and complex geometry at low cost 2 The plastic injection molding process is a cyclic process There are four signi cant stages in the process These stages are lling packing cooling and ejection The plastic injec tion molding process begins with feeding the resin and the appropriate additives from the hopper to the heating injection system of the injection plastic injection molding machine 3 This is the lling stage in which the mould cavity is lled with hot polymer melt at injection temperature After the cav ity is lled in the packing stage additional polymer melt is packed into the cavity at a higher pressure to compensate the expected shrinkage as the polymer solidi es This is followed Corresponding author E mail address saihong eng upm edu my S H Tang by cooling stage where the mould is cooled until the part is suf ciently rigid to be ejected The last step is the ejection stage in which the mould is opened and the part is ejected after which the mould is closed again to begin the next cycle 4 The design and manufacture of injection molded poly meric parts with desired properties is a costly process domi nated by empiricism including the repeated modi cation of actual tooling Among the task of mould design designing the mould speci c supplementary geometry usually on the core side is quite complicated by the inclusion of projection and depression 5 In order to design a mould many important designing factors must be taken into consideration These factors are mould size number of cavity cavity layouts runner systems gating systems shrinkage and ejection system 6 In thermal analysis of the mould the main objective is to analyze the effect of thermal residual stress or molded in stresses on product dimension Thermally induced stresses develop principally during the cooling stage of an injection molded part mainly as a consequence of its low thermal conductivity and the difference in temperature between the molten resin and the mould An uneven temperature eld exists around product cavity during cooling 7 0924 0136 see front matter 2005 Elsevier B V All rights reserved doi 10 1016 j jmatprotec 2005 06 075260 S H Tang et al Journal of Materials Processing Technology 171 2006 259 267 During cooling location near the cooling channel experi ences more cooling than location far away from the cooling channel This different temperature causes the material to experience differential shrinkage causing thermal stresses Signi cant thermal stress can cause warpage problem There fore it is important to simulate the thermal residual stress eld of the injection molded part during the cooling stage 8 By understanding the characteristics of thermal stress distribu tion deformation caused by the thermal residual stress can be predicted In this paper the design of a plastic injection mould for producing warpage testing specimen and for performing ther mal analysis for the mould to access on the effect of thermal residual stress in the mould is presented 2 Methodology 2 1 Design of warpage testing specimen This section illustrates the design of the warpage testing specimen to be used in plastic injection mould It is clear that warpage is the main problem that exists in product with thin shell feature Therefore the main purpose of the prod uct development is to design a plastic part for determining the effective factors in the warpage problem of an injection moulded part with a thin shell The warpage testing specimen is developed from thin shell plastics The overall dimensions of the specimen were 120 mm in length 50 mm in width and 1 mm in thickness The material used for producing the warpage testing specimen was acrylonitrile butadiene stylene ABS and the injection temperature time and pressure were 210 C 3 s and 60 MPa respectively Fig 1 shows the warpage testing specimen pro duced 2 2 Design of plastic injection mould for warpage testing specimen This section describes the design aspects and other consid erations involved in designing the mould to produce warpage testing specimen The material used for producing the plastic Fig 1 Warpage testing specimen produced injection mould for warpage testing specimen was AISI 1050 carbon steel Four design concepts had been considered in designing of the mould including i Three plate mould Concept 1 having two parting line with single cavity Not applicable due to high cost ii Two plate mould Concept 2 having one parting line with single cavity without gating system Not applicable due to low production quantity per injection iii Two plate mould Concept 3 having one parting line with double cavities with gating and ejection system Not applicable as ejector pins might damage the product as the product is too thin iv Two plate mould Concept 4 having one parting line with double cavities with gating system only used sprue puller act as ejector to avoid product damage during ejection In designing of the mould for the warpage testing spec imen the fourth design concept had been applied Various design considerations had been applied in the design Firstly the mould was designed based on the platen dimen sion of the plastic injection machine used BOY 22D There is a limitation of the machine which is the maximum area of machine platen is given by the distance between two tie bars The distance between tie bars of the machine is 254 mm Therefore the maximum width of the mould plate should not exceed this distance Furthermore 4 mm space had been reserved between the two tie bars and the mould for mould setting up and handling purposes This gives the nal max imum width of the mould as 250 mm The standard mould base with 250 mm 250 mm is employed The mould base is tted to the machine using Matex clamp at the upper right and lower left corner of the mould base or mould platen Dimen sions of other related mould plates are shown in Table 1 The mould had been designed with clamping pressure having clamping force higher than the internal cavity force reaction force to avoid ashing from happening Based on the dimensions provided by standard mould set the width and the height of the core plate are 200 and 250 mm respectively These dimensions enabled design of two cavities on core plate to be placed horizontally as there is enough space while the cavity plate is left empty and it is only xed with sprue bushing for the purpose of feeding molten plastics Therefore it is only one standard parting line was designed at Table 1 Mould plates dimensions Components Size mm width height thickness Top clamping plate 250 250 25 Cavity plate 200 250 40 Core plate 200 250 40 Side plate support plate 37 250 70 Ejector retainer plate 120 250 15 Ejector plate 120 250 20 Bottom clamping plate 250 250 25S H Tang et al Journal of Materials Processing Technology 171 2006 259 267 261 the surface of the product The product and the runner were released in a plane through the parting line during mould opening Standard or side gate was designed for this mould The gate is located between the runner and the product The bottom land of the gate was designed to have 20 slanting and has only 0 5 mm thickness for easy de gating purpose The gate was also designed to have 4 mm width and 0 5 mm thickness for the entrance of molten plastic In the mould design the parabolic cross section type of runner was selected as it has the advantage of simpler machin ing in one mould half only which is the core plate in this case However this type of runner has disadvantages such as more heat loss and scrap compared with circular cross section type This might cause the molten plastic to solidify faster This problem was reduced by designing in such a way that the runner is short and has larger diameter which is 6 mm in diameter It is important that the runner designed distributes material or molten plastic into cavities at the same time under the same pressure and with the same temperature Due to this the cavity layout had been designed in symmetrical form Another design aspect that is taken into consideration was air vent design The mating surface between the core plate and the cavity plate has very ne nishing in order to prevent ashing from taking place However this can cause air to trap in the cavity when the mould is closed and cause short shot or incomplete part Suf cient air vent was designed to ensure that air trap can be released to avoid incomplete part from occurring The cooling system was drilled along the length of the cavities and was located horizontally to the mould to allow even cooling These cooling channels were drilled on both cavity and core plates The cooling channels provided suf cient cooling of the mould in the case of turbulent ow Fig 2 shows cavity layout with air vents and cooling channels on core plate In this mould design the ejection system only consists of the ejector retainer plate sprue puller and also the ejector Fig 2 Cavity layout with air vents and cooling channels plate The sprue puller located at the center of core plate not only functions as the puller to hold the product in position when the mould is opened but it also acts as ejector to push the product out of the mould during ejection stage No addi tional ejector is used or located at product cavities because the product produced is very thin i e 1 mm Additional ejec tor in the product cavity area might create hole and damage to the product during ejection Finally enough tolerance of dimensions is given consid eration to compensate for shrinkage of materials Fig 3 shows 3D solid modeling as well as the wireframe modeling of the mould developed using Unigraphics 3 Results and discussion 3 1 Results of product production and modi cation From the mould designed and fabricated the warpage testing specimens produced have some defects during trial run The defects are short shot ashing and warpage The short shot is subsequently eliminated by milling of additional air vents at corners of the cavities to allow air trapped to Fig 3 3D solid modeling and wireframe modeling of the mould 262 S H Tang et al Journal of Materials Processing Technology 171 2006 259 267 Fig 4 Extra air vents to avoid short shot escape Meanwhile ashing was reduced by reducing the packing pressure of the machine Warpage can be controlled by controlling various parameters such as the injection time injection temperature and melting temperature After these modi cations the mould produced high qual ity warpage testing specimen with low cost and required little nishing by de gating Fig 4 shows modi cations of the mould which is machining of extra air vents that can eliminate short shot 3 2 Detail analysis of mould and product After the mould and products were developed the analysis of mould and the product was carried out In the plastic injec tion moulding process molten ABS at 210 C is injected into the mould through the sprue bushing on the cavity plate and directed into the product cavity After cooling takes place the product is formed One cycle of the product takes about 35 s including 20 s of cooling time The material used for producing warpage testing speci men was ABS and the injection temperature time and pres sure were 210 C 3 s and 60 MPa respectively The material selected for the mould was AISI 1050 carbon steel Properties of these materials were important in determin ing temperature distribution in the mould carried out using nite element analysis Table 2 shows the properties for ABS and AISI 1050 carbon steel The critical part of analysis for mould is on the cavity and core plate because these are the place where the product is formed Therefore thermal analysis to study the temperature Fig 5 Model for thermal analysis distribution and temperature at through different times are performed using commercial nite element analysis software called LUSAS Analyst Version 13 5 A two dimensional 2D thermal analysis is carried out for to study the effect of thermal residual stress on the mould at different regions Due to symmetry the thermal analysis was performed by modeling only the top half of the vertical cross section or side view of both the cavity and core plate that were clamped together during injection Fig 5 shows the model of thermal analysis analyzed with irregular meshing Modeling for the model also involves assigning properties and process or cycle time to the model This allowed the nite element solver to analyze the mould modeled and plot time response graphs to show temperature variation over a certain duration and at different regions For the product analysis a two dimensional tensile stress analysis was carried using LUSAS Analyst Version 13 5 Basically the product was loaded in tension on one end while the other end is clamped Load increments were applied until the model reaches plasticity Fig 6 shows loaded model of the analysis 3 3 Result and discussion for mould and product analysis For mould analysis the thermal distribution at different time intervals was observed Fig 7 shows the 2D analysis Table 2 Material properties for mould and product Carbon Steel AISI 1050 mould ABS Polymer product Density 7860 kg m 3 Density 1050 kg m 3 Young s modulus E 208 GPa Young s modulus E 2 519 GPa Poisson s ratio 0 297 Poisson s ratio 0 4 Yield strength S Y 365 4 MPa Yield strength S Y 65 MPa Tensile strength S UTS 636 MPa Thermal expansion 65 10 6 K 1 Thermal expansion 11 65 10 6 K 1 Conductivity k 0 135 W m K Conductivity k 49 4 W m K Speci c heat c 1250 J kg K Speci c heat c 477 J kg K S H Tang et al Journal of Materials Processing Technology 171 2006 259 267 263 Fig 6 Loaded model for analysis of product contour plots of thermal or heat distribution at different time intervals in one complete cycle of plastic injection molding For the 2D analysis of the mould time response graphs are plotted to analyze the effect of thermal residual stress on the products Fig 8 shows nodes selected for plotting time response graphs Figs 9 17 show temperature distribution curves for dif ferent nodes as indicated in Fig 8 From the temperature distribution graphs plotted in Figs 9 17 it is clear that every node selected for the graph plotted experiencing increased in temperature i e from the ambient temperature to a certain temperature higher than the ambient temperature and then remained constant at this temperature for a certain period of time This increase in tem perature was caused by the injection of molten plastic into the cavity of the product After a certain period of time the temperature is then further increased to achieve the highest temperature and remained constant at that temperature Increase in temper ature was due to packing stages that involved high pressure Fig 7 Contour plots of heat distribution at different time intervals 264 S H Tang et al Journal of Materials Processing Technology 171 2006 259 267 Fig 8 Selected nodals near product region for time response graph plots Fig 9 Temperature distribution graph for Node 284 Fig 10 Temperature distribution graph for Node 213 Fig 11 Temperature distribution graph for Node 302 Fig 12 Temperature distribution graph for Node 290 which caused the temperature to increase This temperature remains constant until the cooling stage starts which causes reduction in mould temperature to a lower value and remains at this value The graphs plotted were not smooth due to the absence of function of inputting lling rate of the molten plastic as well as the cooling rate of the coolant The graphs plotted only show maximum value of temperature that can be achieved in the cycle The most critical stage in the thermal residual stress anal ysis is during the cooling stage This is because the cooling Fig 13 Temperature distribution graph for Node 278 S H Tang et al Journal of Materials Processing Technology 171 2006 259 267 265 Fig 14 Temperature distribution graph for Node 1838 Fig 15 Temperature distribution graph for Node 1904 stage causes the material to cool from above to below the glass transition temperature The material experiences differ ential shrinkage that causes thermal stress that might result in warpage From the temperature after the cooling stage as shown in Figs 9 17 it is clear that the area node located near the cooling channel experienced more cooling effect due to fur Fig 16 Temperature distribution graph for Node 1853 Fig 17 Temperature distribution graph for Node 1866 ther decreasing in temperature and the region away from the cooling channel experienced less cooling effect More cool ing effect with quite fast cooling rate means more shrinkage is occurring at the region However the farthest region Node 284 experience more cooling although far away from cooling channel due to heat loss to environment As a result the cooling channel located at the center of the product cavity caused the temperature difference around the middle of the part higher than other locations Compressive stress was developed at the middle area of the part due to more shrinkage and caused warpage due to uneven shrinkage that happened However the temperature differences after cooling for different nodes are small and the warpage effect is not very signi cant It is important for a designer to design a mould that has less thermal residual stress effect with ef cient cooling system For the product analysis from the steps being carried out to analyze the plastic injection product the stress distribution on product at different load factor is observed in the two dimensional analysis Figs 18 21 show the contour plots of equivalent stress at different load increments A critical point Node 127 where the product experiences maximum tensile stress was selected for analysis The stress versus strain curve and the load case versus stress curves at this point were plotted in Figs 22 and 23 From the load case versus stress curves at this point plotted in Fig 23 it is clear that the product experiencing increased in tensile load until it reached the load factor of 23 which is 1150 N This means that the product can withstand tensile load until 1150 N Load higher than this value causes failure to the product Based on Fig 23 the failure is likely to occur at the region near to the xed end of the product wi