購買設計請充值后下載，，資源目錄下的文件所見即所得，都可以點開預覽，，資料完整，充值下載就能得到。。?！咀ⅰ浚篸wg后綴為CAD圖，doc,docx為WORD文檔，有不明白之處，可咨詢Q:1304139763
畢業設計說明書
題 目 多功能汽車發動機
拆裝實驗臺的設計
學生姓名
專 業 交通運輸
班 級 Ｂ０１－１
指導教師
黑 龍 江 工 程 學 院
Design of Directions
The multi-function car launches the machine dismantles the design that pack the experiment set
Candidate：
Specialty：Transportation
Class：B01-1
Supervisor：Teacher
Heilongjiang Institute of Technology
多功能汽車發動機拆裝實驗臺的設計
摘 要
本設計是在研究觀察了現有的發動機拆裝臺架，通過對汽車企業、學?，F(xiàn)有
設備以及通過互連網的搜索，對其結構形式、構造組成、功能以及安裝特點進行分析研究。發現現有的發動機拆裝臺架大多是功能比較單一的類型，這些性能單一的試驗臺架存在著費時、費力、效率低發動機支撐不穩定、拆裝過程中觀察發動機不便等問題。無論是汽車維修企業還是學校都需要一種功能比較齊全的，便于拆裝發動機以及觀察發動機結構的發動機拆裝臺架。而多功能發動機拆裝試驗臺就能很好的解決這一問題。
多功能發動機拆裝試驗臺集翻轉、移動、冷磨于一體很好的解決了以往一
些臺架所存在的一些問題，能基本上滿足汽車維修企業以及學校維修和拆裝發動機的要求。
關鍵詞：發動機；臺架；冷磨；拆裝
The multi-function car launches the machine dismantles the design that pack the experiment set
Abstract
This design is at study observational launch currently the machine dismantles to pack pedestal, pass is current to the car business enterprise, school
Equipments and pass with each other manhunt of connecting the net, as to it's construction form, the structure constitutes, function and install characteristics proceeding analysis research.Discovers to launch currently the machine dismantle to pack pedestal mostly single type in function, the single and on trial pedestal in these functionses exsits to take a lot of time, hard to tackle, the efficiency is low to launch the machine props up unsteady, dismantle to pack to observes to launch the machine inconvenience etc. problem in the process.Wether is a car maintenance business enterprise or the school needs a kind of function more well-found, easy to dismantle to pack to launch machine and observations launch the machine to launch structurally the machine dismantles to pack pedestal.But multi-function launch the machine dismantle to pack to experiment the set and then can be good to resolve this problem.
It is multi-function to launch the machine dismantles to pack to experiment the pedestal gathers inside out, move, cold whet to was good to solve in the integral whole before a
Amount pedestal a some problem for exsitting, can be basic to ascend to satisfy car maintenance business enterprise and schools maintain with dismantle the request that pack launches the machine.
Key phrase:Launch the machine;Pedestal;It is cold to whet;Dismantle to pack
目 錄
摘要 …………………………………………………………………………………………Ⅰ
Abstract ……………………………………………………………………………………Ⅱ
前言 ………………………………………………………………………………………… 1
第一章 實驗臺設計的目的和意義…………………………………………………… 2
1.1 汽車發動機多功能拆裝架的發展趨勢 ………………………………………… 2
1.2 實驗臺設計的目的 ……………………………………………………………… 2
1.3 實驗臺設計的意義 ……………………………………………………………… 2
第二章 多功能發動機拆裝實驗臺的設計…………………………………………… 4
2.1 實驗臺的總體設計要求 ………………………………………………………… 4
2.2 翻轉架的設計 …………………………………………………………………… 5
2.3 臺架的設計 ……………………………………………………………………… 5
2.4 臺架的選材 ……………………………………………………………………… 5
2.5 選擇車型 ………………………………………………………………………… 6
第三章 蝸輪蝸桿減速器的設計……………………………………………………… 7
3.1 蝸輪傳動的組成和特點 ………………………………………………………… 7
3.2 蝸輪蝸桿減速器的設計 ………………………………………………………… 7
3.3 軸的計算 …………………………………………………………………………10
3.4 軸承選擇校核 ……………………………………………………………………12
第四章 聯軸器的選擇和其他零件的確定……………………………………………14
4.1 聯軸器的選擇 ……………………………………………………………………14
4.2 其他零件的確定 …………………………………………………………………14
第五章 總體裝配的設計………………………………………………………………17
5.1 車輪的選擇 ………………………………………………………………………17
5.2 發動機支撐形式的選擇 …………………………………………………………17
5.3 臺架的選材 ………………………………………………………………………17
5.4軸承的選擇及校核 ……………………………………………………………… 18
第六章 電動機的選擇…………………………………………………………………19
第七章 冷磨實驗………………………………………………………………………21
7.1 冷磨注意事項 ……………………………………………………………………21
7.2 冷磨檢查 …………………………………………………………………………21
7.3 冷磨后的拆檢 ……………………………………………………………………22
總結 …………………………………………………………………………………………23
參考文獻 ……………………………………………………………………………………24
致謝 …………………………………………………………………………………………25